What did you build today (Pictures) ?

[berkseo]

@scalz How do you plan to use your dongle? Just as coordinator? or only as a gateway mysensors? Have you tried using it as a combo? zigbee quite unceremoniously uses the resources of the mcu.

[berkseo]

@scalz said in What did you build today (Pictures) ?:

This evening I assembled another dongle (and a few other boards).
@nca78 as you asked, here is a pic during tests. Tiny dual rf dongle board, isn't it

This customization boards adafruit? I've customized the Board Sandeep Mistry.

[simbo]

Air particulate sensor.

BTW, solder fumes seem to be bad for you........

[scalz]

@berkseo

• like I said, MySensors bridge, combo . Yes I know about resources.
  Note: zigbee is out of MySensors scope (not arduino code), so for the moment some ideas and POCs will be local, not making money no ETA, still lot of WIPs and the daily job!
• yes.

[FotoFieber]

Modified a laser filament sensor (pat9125, used with Prusa mk3) to be used with an ESP32.

Maybe I will use it as a filament stuck sensor with octoprint. Or a filament meter?

[pihome]

Very first attempt to solder smd components on pcb with hot air soldering station. lots of mistakes but i m learning...

[zboblamont]

First of the winter projects done, just the programming to finish and replacement temperature chips to get (broke the legs off both DS18B20s through clumsiness).
With mains/battery backup and RTC, it will record boiler start/stop and run times as well as feed/return temperatures, and as an aside the inevitable power cuts which plague this part of the world.
The MCU plugs into a socketed backplane hot-glued to the back of the box should removal prove necessary, but quite pleased it is sturdy and all fitted into a slim 25mm deep standard (cheap) box.

[berkseo]

My brand new device on nRF52840. It is a light and shock(vibration) sensor.

Two sensors are used, max44009 light sensor (1 ua) and lis2dw accelerometer (1 ua).

The light sensor measures in Lux.

The shock sensor has five levels of sensitivity.

Two modes of operation: main (working) mode and command reception mode.

The sensor accepts settings: the interval of sending data from the light sensor (in minutes), sending recalculated light data from Lux to watts per meter squared(on/off), the sensitivity level of the shock sensor(5 levels, 1 to 5)

Depending on which sensors are installed on the PCB, it can be used only as a light sensor, only as a shock sensor or both.

In the near future the project will be posted on openhardware.io

video (inside view of the sensor, an example of working with a smart home, an example of setting): - https://youtu.be/I2ywIxp-RsE

[NeverDie]

@berkseo this would also be good for monitoring when the trash cans get picked up by the garbage truck. If it has enough range that is. Of course that wouldn't apply to high rise dwellers, but for people in houses it would be a nice perk.

[pihome]

working on GPIO MySensors Gateway

[berkseo]

An updated version of my temperature and humidity sensor with e-ink. Now on nRF52840. Now it is not a module but a device in the case.

Replaced temperature sensor sht20 -- > > si7020
Added accelerometer.

In the near future the project will be posted updated on the website openhardware.io

Video: https://youtu.be/T66y83lF-xg

[franz-unix]

Amazing! 😃

The case is 3d printable?

[berkseo]

@franz-unix
This is made on SLA printer, but should normally print on FDM

[pihome]

@pihome just realized one big blunder, The NSS, MOSI and SCK are not 5V tolerant on RFM69. hence need level converter :(
i was wondering is there any one ic can can do instead i have to used BSS138 per pin.

[NeverDie]

@berkseo I'm quite interested in a schematic view showing how the epaper gets wired up, because priced just by itself epaper seems like an affordable solution.

aliexpress.com/item/32962453684.html?spm=a2g0o.productlist.0.0.3e97287fLkUbFb&algo_pvid=9af4e6cf-0e45-470a-925d-b0b1d62212d5&algo_expid=9af4e6cf-0e45-470a-925d-b0b1d62212d5-0&btsid=e444f3d1-9949-4c49-ada6-376ecc83a846&ws_ab_test=searchweb0_0,searchweb201602_8,searchweb201603_55

or

https://www.aliexpress.com/item/32810660608.html?spm=a2g0o.detail.1000013.1.10ee3442rep8pS&gps-id=pcDetailBottomMoreThisSeller&scm=1007.13339.146401.0&scm_id=1007.13339.146401.0&scm-url=1007.13339.146401.0&pvid=8e948464-a786-4cf4-96ff-86c51f67bf4c

On the other hand, if one has to rely on adafruit or similar for an epaper breakout board to make use of it, the effective price jumps by around 5-6x or so.

[monte]

@neverdie you can use this and this as a reference. No need to buy ready breakout board, if you know how to trace your own.

[bjacobse]

https://github.com/dkjonas/Wavin-AHC-9000-mqtt
iron and toner transfer, then etched and soldered and finally acrylic spray on cobber so it won't corrode

[Nca78]

Hello, as it was getting seriously off topic, I moved the discussion related to SLA printing of enclosure to here :
https://forum.mysensors.org/topic/10815/printing-enclosures-with-sla-printers

Feel free to suggest a better title.

[nagelc]

I've had surprisingly good luck buying cheap parts from Ali-express, but not this time. I bought an NRF52832 iBeacon that supposedly had an SHT30 temperature sensor and KX022 accelerometer. When the parts arrived, neither of those parts were populated. All the beacon has is a push button.

I was able to program it to work with MySensors, however. With only SWIO and SWCLK (no txt out), I took @scalz advice (in another topic) and used a J-Link EDU Mini so I could use the RTT app to get printf style debugging. That worked nicely and I learned a new tool.

Perhaps I can use the iBeacon button for a remote.

[berkseo]

Yesterday I finished my new project. This is motion sensor (S16-L201D) + light sensor (MAX44009) + temperature and humidity sensor (SI7020). Рowered by nRF52840.

..upd
video - https://youtu.be/cbJYam4jo2g