Hello everybody.
Since i discover this awesome project open source (mysensors) and the awesome work done here, i have been converted all my arduinos to Mysensor library ,because i already had Vera lite managing my home.

so lets share what i already did. **Pictures!!!! **

First, my gateway:
i used a round small box , a ftdi adapter,and a 5v promini with 3.3v regulator on nrf24 .
On picture is a normal nrf24 but then i use a amplified version that have an coaxial cable connected and an 2.4ghz antenna on outside roof(attach to my external TV antenna) ,So i can receive and send information to all my incoming sensors ,in all my garden(+3500m2) and it can receive inside home signal aswell.

And then ,on 3rd day ,I created an irrigation control......

Its not tested on vera yet, but at first look i have some work to do before it work properly. And i need replace this power wires for 12vpower adapter ones.

Look at the switch ... you cant see it ... but its inside top rubber. just press on rubber and its water proof

Sory about my English errors ,not my natural language:P

Do you think you've seen all kinds of projects here? So ..think again.
There it is my chicken eggs encubator .
Made from a 25 liters plastic storage box and some foam outside to prevent heat loss.
i used 2 X 18w halogen g9 bulbs and a 230v dimmer to decrease light brightness.

There is a diagram above from fritzing. I uses an main arduino that controls a SSR relay for controls halogen light bulbs. this light bulbs are dimmed to half(in my case)
for hold temperature much time as possible without decrease temperature.That makes SSR stay on for some minutes before goes off again. if halogen light are to powerfull makes the SSR goes on and off many times in short period. the ideal situation is having the dimmer controlled by arduino and hold temperature without turn ligh off ,but i didn't got this dimmer yet(is there any one ready for try it? ).

this is the 3rd version i build and all the other version hatch almost all eggs(+/-80%) even with some issues on controlling temperature.i only had 1 fan and that caused some zones that overheated (more on coners).
Now i have 2x120mm(0.10A) pc fans that can spread hot air the same way in all this box.

Then i have a secondary arduino that it's for safe features. it controls an alarm buzzer(pc speaker) ,its connected to an temperature sensor (ds18b20) and send temperature to emoncms.com through an nrf24 wireless board
If temperatures goes over 39ºC or below 30ºC it sound an noisy alarm.Just in case main arduino or DHT22 fail.

Egg roller its made os aluminium and plastic egg racks cutted and glued with hot glue(screws were better but this is enought to hold eggs).it makes 45º each side.
An High torque servo roll every 60 minutes. Note that an regular servo does not have enough torque should be an high toque version.

eggs ready to start hatching! note the ds18b20 sensor in the back of the DHT22 sensor.they will stay same height than egg rack.

2x18w halogen lighs

lcd screen is configured for simplicity . code have hours and days passed and remaining ,but i decide use just passed days, temperature manual offset and time for next egg roll(minutes),and of course temperature and humidity on first line.

its a mess of cables ...i know. It's what happening when we always improve our project until it be a final version
I used usb cables from computer cases for wire sensors, it work really well .
There's 2 solid state relays on picture but we only need one.

Parts:
2x 12v 120mm pc fan(0.10A -slow speed/low noise)
1x LM2596
1x High torque servo or step motor(need additional controller).
1x 5v Arduino pro mini (or equivalent )
1x DHT22
1x 5v relay Or SSR G3MB-202P Solid State
1x 2 lines I2C 1602 LCD (i2c ,not serial) or 4 lines if you what more info on screen like time left and time spent clock.
2x monetary switch
2x 10k resistors
2x 18w halogen light bulbs
2x G9 Ceramic Sockets
1x AC 220V 2000W SCR Voltage Regulator (overkill for 36W i know, but it cost 1.50€ on ebay)

Optional parts
1x 3.3v pro mini (or equivalent)
1x computer speaker(buzzer)
1x DS18b20
1x NRF24L01
1x 4.7K Resistor
1x 3.7v litio battery (cellphone or 18650 cell)
1x Battery Protection Board(just for charge battery before start hatching)
note: this battery just hold main arduino in case of power failure. During normal work it never charge or discharge due 5v on line from LM2526

FRITZING PROJECT:
0_1504458462680_eggencubator v2.fzz

CODE:

// Servo version of
// Incubator code with lcd 16x2 ####--->>  I2C (4 wires) <<---  ###
// ---------------------------------------------
#include <Wire.h>
#include <LiquidCrystal_I2C.h>

#include "DHT.h"
#include <Servo.h>
#define DHTPIN 4                              // Define the temp sensor data pin
#define DHTTYPE DHT22                         // define the temp/hum sensor type
#define RELAY_1  7                              // define the relay 1 and 2 control pin
#define RELAY_2  8

 
Servo myservo;                                // create servo object to control a servo
DHT dht(DHTPIN, DHTTYPE);                     //initialize the temp sensor

LiquidCrystal_I2C lcd(0x3F,2,1,0,4,5,6,7,3, POSITIVE);    //set up what port the LCD will use
                      
int pos = 0;                                  // variable to store the servo position
int istate = 0;

const int  buttonPin1 = 5;    // the pin that the Up pushbutton is attached to
const int  buttonPin2 = 6;    // the pin that the Down pushbutton is attached to
int buttonState1 = 0;
int buttonState2 = 0;
float val = 0; //val to increment/decrement (buttons/ threshold)

int is, im, ih, id, ida, iha, ima;                      // variables for time
float time, s1, m1, h1, d1;                   //  Set up variables to calculate time
int ic, ip, ik;
byte thermo[8] = {B00100, B01010, B01010, B01110, B01110, B11111, B11111, B01110}; //thermometer icon
byte drop[8] = {B00100, B00100, B01010, B01010, B10001, B10001, B10001, B01110}; //drop icon
byte arrow[8] = { B00100,  B01010,  B10101,  B00100, B10101,  B01010,  B00100,}; // smile icon
byte tim[8] = {B00000, B01110, B10101, B10101, B10011, B10001, B01110,}; // clock icon

int END = 0;
unsigned long previousMillis = 0;
const long interval = 3600000UL; //timer for roll eggs 1HOUR

void setup()
{
 Serial.begin(9600);

  pinMode(buttonPin1, INPUT);
  pinMode(buttonPin2, INPUT); 
  dht.begin();                                //start the temp sensor
  pinMode(RELAY_1, OUTPUT);
  pinMode(RELAY_2, OUTPUT);
  
  lcd.begin (16,2);                          // columns, rows.  use 16,2 for a 16x2 LCD, etc.
  lcd.clear();                                // start with a blank screen
  lcd.setCursor(0, 0);                        // set cursor to column 0, row 0 (the first row)
  lcd.print("Incubatora 1.0");                 // opening line
  lcd.setCursor(0, 1);                        // set cursor to column 0, row 1
  lcd.print("A iniciar!");
  delay(2000);
                          
  lcd.createChar(0, thermo);
  lcd.createChar(1, drop);
  lcd.createChar(2, arrow);
  lcd.createChar(3, tim);
  myservo.attach(9); // servo control is set to pin 9 (usually yellow wire is control, black goes to ground red goes to +5V)
  myservo.write(70); //put the servo at intitial position of 16 degrees
  myservo.detach();
}

//loop to read the sensor and display
void loop() {

  int buttonState1 = digitalRead(buttonPin1);
  int buttonState2 = digitalRead(buttonPin2);
  delay(10);

if (buttonState1 == HIGH)
     {     
     val-=0.1;
    } 
   else if (buttonState2 == HIGH) 
   { 
    val+=0.1;
   }
    
     
     
  float h = dht.readHumidity();                 // Read the humidity
  float t = dht.readTemperature();              // Read temperature in celsius
  float f = dht.readTemperature(true);          // get the temperature in Fahreheit
  
   //Temperature controller
    if (t >= (37.7 + val))
    {                       //  Set the temperature for the relay to come on (ideal 37.7ºC)     
      digitalWrite(RELAY_1,LOW);          // TO HOT: Turns Relay OFF
    digitalWrite(RELAY_2,LOW);
    }

     if (t <= (37.5 + val))
   {                       //  Set the temperature for the relay to come on (ideal 37.7ºC)    
      digitalWrite(RELAY_1,HIGH);          // TO HOT: Turns Relay ON
    digitalWrite(RELAY_2,HIGH);
    }
  
  
  // uncomment to compute heat index in Fahrenheit (the default)
  //float hif = dht.computeHeatIndex(f, h);
  // Compute heat index in Celsius (isFahreheit = false)
  //float hic = dht.computeHeatIndex(t, h, false);
  time = millis();                            //  Get time in milliseconds since tunit turn on
  s1 = time / 1000;                           //  Convert time to seconds, minutes, hours, days
  m1 = s1 / 60;
  h1 = m1 / 60;
  d1 = h1 / 24;
  id = int(d1);  //d                             //  Strip out remainder to leave Days:Hours:Minutes:Seconds
  ih = int((d1 - int(d1)) * 24); //h
  im = int((h1 - int(h1)) * 60); //m
  is = int((m1 - int(m1)) * 60);  //s
 
  
  
  
  // Calculate approximate TIME till hatch (assume 21 days to hatch)   -      not used yet
  ida = 21 - id;
  iha = 24 - ih;   
  ima = 60 - im;
  


  
  if (isnan(h) || isnan(t) || isnan(f)) {
    // if sensor can't be read
    lcd.clear();
    lcd.setCursor(0, 0);
    lcd.print("Falha No Sensor");
    Serial.print("Falha No Sensor" );
     digitalWrite(RELAY_1,HIGH);          // ERRO: Turns 1 Relay OFF to not kill all the eggs
    digitalWrite(RELAY_2,LOW);
    delay(5000);
    return;
  }
  else {      //  for  LCD 16x2
    //sensor was read succesfully so print values to LCD 16x2
    lcd.clear();                                // Clear the LCD
    //Print temperature and humidity in first two lines
    lcd.setCursor(0, 0);
    // lcd.print("Temperature:");

    lcd.write(byte(0));                       // Write the Thermometer icon
     lcd.print(t , 1);
    lcd.print((char)223);
    lcd.print("C  ");
    
    //lcd.setCursor(0,1);
    lcd.write(byte(1));                         // Write the drop icon
    // lcd.print("Humidade:");
     lcd.print(h, 0);
     lcd.print("%");
  //   lcd.print(" ");
  //  lcd.print(ic);
    lcd.setCursor(0, 1);
    
    //lcd.print("  ");
    lcd.write(byte(3));
    lcd.print(" ");
    // Print timein format Time: xxd:xxh:xxm:xxs
  lcd.print(id);
    lcd.print("d ");
   /* lcd.print(ih);
    lcd.print(":");
    lcd.print(im);
    lcd.print(" "); 
    lcd.print(is); lcd.print(" ");*/
    lcd.print(val,1);    


  if (21 - id <= 3){
       // Print days left till hatch
       lcd.print("!");
     END = 1; //stop move eggs
   }
  
   // this section is to roll the eggs   
unsigned long currentMillis = millis();

 int tleft = ((currentMillis - previousMillis)/ 1000) /60;
lcd.print(" ");  lcd.write(byte(2));  
 lcd.print(tleft); 

 
if (currentMillis - previousMillis >= interval)
{
  previousMillis = currentMillis;
 
if(istate == 0 && END == 0){  
  //myservo.attach(9);
   for (pos = 80; pos <= 155; pos += 1) { // goes from 16 degrees to 80 degrees  in steps of 1 degree
     myservo.attach(9);
     myservo.write(pos);
     istate=1;
     delay(50);
   }
   myservo.detach();
 }
else if( istate == 1 && END == 0)
{ 
 // myservo.attach(9);        
   for (pos = 155 ; pos >=80; pos -= 1) { // goes from 80 degrees to 0 degrees
    myservo.attach(9);
     myservo.write(pos); 
     istate = 0;
     delay(50);                      // slow the servo down a bit to turn the eggs        
   }
   myservo.detach();
 }

}
  
       // Pause for 2 seconds
   delay(2000);
  }
}
 

auxiliary/optional arduino

#define MY_DEBUG



// ---------------------------------------------
#define MY_RADIO_NRF24


#include <SPI.h>
#include <MySensors.h>  
#include <OneWire.h>
#include <DallasTemperature.h>


#define MY_RF24_PA_LEVEL RF24_PA_LOW

// Data wire is plugged into pin 2 on the Arduino
#define ONE_WIRE_BUS 2
 #define CHILD_ID_EGG 12 //id
// Setup a oneWire instance to communicate with any OneWire devices 
// (not just Maxim/Dallas temperature ICs)
OneWire oneWire(ONE_WIRE_BUS);
 
// Pass our oneWire reference to Dallas Temperature.
DallasTemperature sensors(&oneWire);
const int buzzer = 3; //buzzer to arduino pin 3
unsigned int al = 0;

bool receivedConfig = false;
bool metric = true;
MyMessage msg(CHILD_ID_EGG,V_TEMP);


unsigned long previousMillis = 0;        // will store last time sent temperature
const long interval =900000; //15min

void before()
{
  // Startup up the OneWire library
  sensors.begin();
}

void setup()
{
  
      sensors.begin();
       pinMode(buzzer, OUTPUT); // Set buzzer - pin 9 as an output
}


void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Temperature eggs", "2.0");

 
  // Present all sensors to controller
       present(CHILD_ID_EGG, S_TEMP);
  }



void loop() {

  sensors.requestTemperatures(); // Send the command to get temperatures


  //Serial.print("Temperature is: ");

    float t =sensors.getTempCByIndex(0); 

//Serial.print(t); 
//-----------------------------timer & send-------------------------------------
 unsigned long currentMillis = millis();

  if (currentMillis - previousMillis >= interval) {
       
        previousMillis = currentMillis;
       
// Send in the new temperature every 5min send(msg.setSensor(t).set(t,1));  
send(msg.set(t,1));  Serial.print(t); 
  }
//---------------------------------------------------------------------------------------

//alarm buzzer-------
 if (t >=37.0) {    //(37ºc)
  al=1;                 //save 1 when 1st temperature estabilize. after that "al" will be always 1 until reset/shutdows . This makes the alarm not start when incubator still cold on warm up
   }                      

   //Temperature controller alarm
    if (t >= 39.0) {  
      for (unsigned int i=750; i<2500; i++) {  // TO HOT: alarm!
      tone(buzzer, i ,700);
        delayMicroseconds (15);
      }
delay(2000);
    }

        
  if (t <= 30.0 && al == 1) {                       
 
      for (unsigned int i=750; i<2500; i++) {  // TO HOT: alarm!
      tone(buzzer, i ,700);
        delayMicroseconds (15);
      }
delay(2000);
    }

 
    
  }

NOTE: English it's not my language. i'm sorry some errors that can happens

hello. like o wrote before my veralite dies after 4 years of work.
So now i'm on Domoticz.For the dead vera lite i recover the z-wave part. i had some doubts that it works but i have seen n razberry cards that the hardware its the same,so why not try.
I just cutted the 4 layers pcb and solder 4 wires on zm3102 chip directly(tx,rc,vcc and gnd). some hot glue and some nail polish /or epoxy to seal cutted sides.There are no working leds but how cares. and yea.I have an external antena . Everything fits inside vera case aswell(recycling on the best),raspbery,zwave card and mysensors GW.
in beginning domoticz didn't detect it like in official zwave cards ,there are some procedures to make before,but soon as setup button gets blue ,was just reset or exclude and then include nodes again on Domoticz. until now (24hours later) everything still work like a charm ,And let me say Domoticz is far more complete than mios os.

@zboblamont said in #define DEFAULT_RFM69_IRQ_PIN:

So long as these are set before including the MySensors library it should indeed override the defaults.

OMG. this is the problem! i was defining AFTER Including Mysensors library. well i should knew that if i know more about programing

this code now is working comunicating well.

I still having an issue. termometer doesn't appear on domoticz. i think it's well presented... i'm not sure whats happen. but the axel for angle, that i need is , working good already .

The corret statement is .
#define MY_RFM69_IRQ_PIN 3
#define MY_RFM69_IRQ_NUM 1

/*
 ->  __  __       ____
 -> |  \/  |_   _/ ___|  ___ _ __  ___  ___  _ __ ___
 -> | |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __|
 -> | |  | | |_| |___| |  __/ | | \__ \  _  | |  \__ \
 -> |_|  |_|\__, |____/ \___|_| |_|___/\___/|_|  |___/
 ->         |___/                      2.3.2
*/

#define MY_DEBUG
#include <basicMPU6050.h> 
#define MY_RADIO_RFM69
#define MY_RFM69_IRQ_PIN 3 //!< DEFAULT_RFM69_IRQ_PIN
#define MY_RFM69_IRQ_NUM 1
#include <MySensors.h>
#include <RunningMedian.h>
RunningMedian samples = RunningMedian(100);

#define CHILD_ID 98
#define CHILD_ID_TEMP 99



MyMessage msg(CHILD_ID, V_LEVEL);
MyMessage msg1(CHILD_ID_TEMP,V_TEMP);
// Create instance
basicMPU6050<> imu; //credits:https://github.com/RCmags/basicMPU6050
 float incl;
 
  static uint8_t sentValue;
void presentation()
{
  // Send the sketch version information to the gateway and controller
  sendSketchInfo("TANQUE", "2.3");

  // Register all sensors to gw (they will be created as child devices)
    present(CHILD_ID, S_MOISTURE);
     present(CHILD_ID_TEMP,S_TEMP);
}

 
void setup() {
  // Set registers - Always required
  imu.setup();

  // Initial calibration of gyro
  imu.setBias();

  
}

void loop() { 
  // Update gyro calibration 
   imu.updateBias();
  
   incl= imu.ay();

   int val = ((incl+1)*50);

   int x = val;
  
  samples.add(x); 
 
 //long m = samples.getAverage(); 
  int m = samples.getMedian();
  delay (200);

        
  if (m != sentValue)
   {
   
 
   send(msg.set(m));
   float temp = imu.temp();
  send(msg1.set(temp,1));
  sentValue = m;
  delay (5000);
  
   }
}   

if it is an emergency button should be connected directly to relay (connected by hardware). And not using code,because if arduino it's freezed it will not respond and you cant stop it

Hi to @Greymarvel .Well i already seen this movie before. I bought diferent nrf24 nodes,amplifed ,not amplified,with or without capacitors. In fact i had worst redults with amp nodes. I just change to rfm69hw and w
. No more low power/high power...etc. now i got my 4000m2 terrain covered (around 80m long).
I didn't check max range but i never had lost a packet again. I was a very good increment on my network stability.
That fake nrf24 chips are crazy and unstable and yes,all ebay cheap nodes are fake second i know.

And that is the result . 14 chicks of 25eggs ,but i could say that was 100% sucess because the other eggs were not fertilized. not even a single dead before or after hatch. Its not the arduino the most versatile machine?

top left chic just born 10min before i take the picture:P

thank you for reply @mfalkvidd
Payload like 100 shoud be 100% on domoticz, right? how does domoticz "know" that a blindcover /or shutter is open or close? because it's not respondig to that...

 
 __  __       ____
|  \/  |_   _/ ___|  ___ _ __  ___  ___  _ __ ___
| |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __|
| |  | | |_| |___| |  __/ | | \__ \  _  | |  \__ \
|_|  |_|\__, |____/ \___|_| |_|___/\___/|_|  |___/
        |___/                      2.3.1

16 MCO:BGN:INIT NODE,CP=RRNNA---,REL=255,VER=2.3.1
26 MCO:BGN:BFR
28 TSM:INIT
30 TSF:WUR:MS=0
34 TSM:INIT:TSP OK
34 TSF:SID:OK,ID=4
36 TSM:FPAR
1257 TSF:MSG:SEND,4-4-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
1423 TSF:MSG:READ,0-0-4,s=255,c=3,t=8,pt=1,l=1,sg=0:0
1429 TSF:MSG:FPAR OK,ID=0,D=1
3264 TSM:FPAR:OK
3264 TSM:ID
3266 TSM:ID:OK
3268 TSM:UPL
3276 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
3315 TSF:MSG:READ,0-0-4,s=255,c=3,t=25,pt=1,l=1,sg=0:1
3321 TSF:MSG:PONG RECV,HP=1
3325 TSM:UPL:OK
3328 TSM:READY:ID=4,PAR=0,DIS=1
3540 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
3567 TSF:MSG:READ,0-0-4,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
3786 TSF:MSG:SEND,4-4-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.3.1
4005 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
4046 TSF:MSG:READ,0-0-4,s=255,c=3,t=6,pt=0,l=1,sg=0:M
4263 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=11,pt=0,l=5,sg=0,ft=0,st=OK:Cover
4483 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:2.0
4708 TSF:MSG:SEND,4-4-0-0,s=0,c=0,t=5,pt=0,l=22,sg=0,ft=0,st=OK:shuttle for Livingroom
4716 MCO:REG:REQ
4929 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
4956 TSF:MSG:READ,0-0-4,s=255,c=3,t=27,pt=1,l=1,sg=0:1
4962 MCO:PIM:NODE REG=1
4964 MCO:BGN:STP
getting rolltime from eeprom: 
28.00
getting state from eeprom: 
0
4968 MCO:BGN:INIT OK,TSP=1
Sending initial value
5185 TSF:MSG:SEND,4-4-0-0,s=0,c=1,t=29,pt=1,l=1,sg=0,ft=0,st=OK:0
5402 TSF:MSG:SEND,4-4-0-0,s=0,c=1,t=30,pt=1,l=1,sg=0,ft=0,st=OK:0
5619 TSF:MSG:SEND,4-4-0-0,s=0,c=1,t=31,pt=1,l=1,sg=0,ft=0,st=OK:1
5838 TSF:MSG:SEND,4-4-0-0,s=0,c=1,t=3,pt=2,l=2,sg=0,ft=0,st=OK:0

.
.
.
.
after I give an order of CLOSE (DOWN) shutter (v_percentage=0)

------------     *(HERE WAS AT 100% AND I ORDER TO GO 0%(CLOSED)* -------------------

exiting incoming message
Shutters going down
612509 TSF:MSG:SEND,4-4-0-0,s=0,c=1,t=29,pt=1,l=1,sg=0,ft=0,st=OK:0
612728 TSF:MSG:SEND,4-4-0-0,s=0,c=1,t=30,pt=1,l=1,sg=0,ft=0,st=OK:1
612947 TSF:MSG:SEND,4-4-0-0,s=0,c=1,t=31,pt=1,l=1,sg=0,ft=0,st=OK:0
613167 TSF:MSG:SEND,4-4-0-0,s=0,c=1,t=3,pt=2,l=2,sg=0,ft=0,st=OK:100
99
98



(...)

7
6
5
4
3
2
1
0
Shutters halted X
saving state to: 
0
645519 TSF:MSG:SEND,4-4-0-0,s=0,c=1,t=29,pt=1,l=1,sg=0,ft=0,st=OK:0
645738 TSF:MSG:SEND,4-4-0-0,s=0,c=1,t=30,pt=1,l=1,sg=0,ft=0,st=OK:0
645957 TSF:MSG:SEND,4-4-0-0,s=0,c=1,t=31,pt=1,l=1,sg=0,ft=0,st=OK:1
646176 TSF:MSG:SEND,4-4-0-0,s=0,c=1,t=3,pt=2,l=2,sg=0,ft=0,st=OK:0

------------    *(HERE REACH 0%)* -------------------

i'm bilding this right now: http://www.qsl.net/eb4eqa/bt_yagi/bt_yagi.htm
i tell you what is the increment of range in the next weekend ...

i have one of temp sensors under a water solar panel and the aluminium from the frame get me crazy because that sensor lose many of the sent reads to gw. i will finish that yagi antenna and solder that to my nrf24 and i hope signal increase performance.

in my house (i dont have neighboard les than 80m with wifi signal and noise from other routers or any king of 2.4ghz signals ) i can send a door sensor signal(from my entrance gate) by 50m and 1 wall . that one have this antena alredy on tx:
http://martybugs.net/wireless/collinear.cgi

because wifi is not the most safe for humans... sleeping etc

what are you talking about???
are you the ones that say wifi boils water on a cup?

mysensors library works on nrf24l01+ modules, Not wifi. its a kind of Bluetooth already... anyway Bluetooth is 2.4ghz like wi-fi, but Bluetooth consumes less power (Theoricly)

Maybe you are right and it's the proximity to a switching tranformer like this hlk-pm01 .They are all on same protoboard aprox 50x60mm. i could build a sheld on it but....now its working with the rfm69version W ok for a few days.
The strange part is this combo was very used a few years now on made pcbs the on forum wher they had the maker/developer contest and never seen a line of this problem...

i believe this problem has to be with rfm69CW and not the rfm69W . i have boot versions 868mhz and normally always the CW cause me this issues if is not batery powered even with 100uf +100nf caps filtering on transformer out, caps on the rfm60 power etc... maybe they are fake or have any problem. . i just ordered new rfm69W board and let me see if get better. right now i have like 10 nodes running outdoor on irrigation ,controlling relays and lights ,and metering temperatures. all with RFM69W ans HW ,this CW always give problems...

Hello . it's the 3rd node that i build with the combo arduino promini 3.3v + hlk-pm01 + rfm69 and all need wire ground to earth (on wallsocket) to let rfm69 comunicate.
otherwise will fail on every comunication even near Gateway...
Personally i only think in noise.but everyone say that hlk-pm01 are low noise.
I'm not using any cap after hlk-pm01 for snooth voltage but i already try it before without better result.
rfm69 is powered by the pro mini integrated regulator.
Any one had this problem?

Now is working. so what i did is call to children 0 and 1 and #define MY_NODE_ID 101 ,so next node appear on harware/mysensors gw ,and apear on devices as IDX 99 and 100... The auto node idx from domoticz shoud have caused some issue.... now is working

this is my gw . in fact i never understud very well the child thing. last one is "tanque"( tank) is ths node that we talk and is showing as 13 ?? why?

normally what i do is go to devices ,see what next id is available and atribute it to children..worked until now but i think its wrong

@zboblamont said in #define DEFAULT_RFM69_IRQ_PIN:

ode sketch to print locally over serial t

this is local log already. thal last line: 11233 TSF:MSG:SEND,4-4-0-0,s=99,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:36.5
is the message sending 36.5 degrees to gateway.

domoticz log report message received from this node...but is not even on devices...

this is the log. everything appear be fine with presetation of gyro termometer .But never show on devices. someting wrong with my gateway...

1282 TSF:MSG:READ,7-7-4,s=255,c=3,t=8,pt=1,l=1,sg=0:1
2050 TSM:FPAR:OK
2050 TSM:ID
2052 TSM:ID:OK
2054 TSM:UPL
2062 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2101 TSF:MSG:READ,0-0-4,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2107 TSF:MSG:PONG RECV,HP=1
2111 TSM:UPL:OK
2113 TSM:READY:ID=4,PAR=0,DIS=1
2326 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2353 TSF:MSG:READ,0-0-4,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2572 TSF:MSG:SEND,4-4-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.3.2
2791 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
2828 TSF:MSG:READ,0-0-4,s=255,c=3,t=6,pt=0,l=1,sg=0:M
3250 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=11,pt=0,l=6,sg=0,ft=0,st=OK:TANQUE
3469 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:2.3
3688 TSF:MSG:SEND,4-4-0-0,s=98,c=0,t=35,pt=0,l=0,sg=0,ft=0,st=OK:
3905 TSF:MSG:SEND,4-4-0-0,s=99,c=0,t=6,pt=0,l=0,sg=0,ft=0,st=OK:
3911 MCO:REG:REQ
4124 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
4151 TSF:MSG:READ,0-0-4,s=255,c=3,t=27,pt=1,l=1,sg=0:1
4157 MCO:PIM:NODE REG=1
4159 MCO:BGN:STP
10801 MCO:BGN:INIT OK,TSP=1
11014 TSF:MSG:SEND,4-4-0-0,s=98,c=1,t=37,pt=2,l=2,sg=0,ft=0,st=OK:49
11233 TSF:MSG:SEND,4-4-0-0,s=99,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:36.5

@zboblamont said in #define DEFAULT_RFM69_IRQ_PIN:

So long as these are set before including the MySensors library it should indeed override the defaults.

OMG. this is the problem! i was defining AFTER Including Mysensors library. well i should knew that if i know more about programing

this code now is working comunicating well.

I still having an issue. termometer doesn't appear on domoticz. i think it's well presented... i'm not sure whats happen. but the axel for angle, that i need is , working good already .

The corret statement is .
#define MY_RFM69_IRQ_PIN 3
#define MY_RFM69_IRQ_NUM 1

/*
 ->  __  __       ____
 -> |  \/  |_   _/ ___|  ___ _ __  ___  ___  _ __ ___
 -> | |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __|
 -> | |  | | |_| |___| |  __/ | | \__ \  _  | |  \__ \
 -> |_|  |_|\__, |____/ \___|_| |_|___/\___/|_|  |___/
 ->         |___/                      2.3.2
*/

#define MY_DEBUG
#include <basicMPU6050.h> 
#define MY_RADIO_RFM69
#define MY_RFM69_IRQ_PIN 3 //!< DEFAULT_RFM69_IRQ_PIN
#define MY_RFM69_IRQ_NUM 1
#include <MySensors.h>
#include <RunningMedian.h>
RunningMedian samples = RunningMedian(100);

#define CHILD_ID 98
#define CHILD_ID_TEMP 99



MyMessage msg(CHILD_ID, V_LEVEL);
MyMessage msg1(CHILD_ID_TEMP,V_TEMP);
// Create instance
basicMPU6050<> imu; //credits:https://github.com/RCmags/basicMPU6050
 float incl;
 
  static uint8_t sentValue;
void presentation()
{
  // Send the sketch version information to the gateway and controller
  sendSketchInfo("TANQUE", "2.3");

  // Register all sensors to gw (they will be created as child devices)
    present(CHILD_ID, S_MOISTURE);
     present(CHILD_ID_TEMP,S_TEMP);
}

 
void setup() {
  // Set registers - Always required
  imu.setup();

  // Initial calibration of gyro
  imu.setBias();

  
}

void loop() { 
  // Update gyro calibration 
   imu.updateBias();
  
   incl= imu.ay();

   int val = ((incl+1)*50);

   int x = val;
  
  samples.add(x); 
 
 //long m = samples.getAverage(); 
  int m = samples.getMedian();
  delay (200);

        
  if (m != sentValue)
   {
   
 
   send(msg.set(m));
   float temp = imu.temp();
  send(msg1.set(temp,1));
  sentValue = m;
  delay (5000);
  
   }
}   

not working.same result .... lets think again.. out of the box... is it possible use same pin form both rfm69 and mpu6050 ? or even not using the int pin on mpu6050... maybe that is the solution...

_IRQ_NUM 1 shoud be the interrupt pin 1. 0 is D2

@zboblamont said in #define DEFAULT_RFM69_IRQ_PIN:

#define MY_RFM69_IRQ_PIN DEFAULT_RFM69_IRQ_PIN

sory, i couldn't understand, to move it to pin 3 shoud be that?:
#define DEFAULT_RFM69_IRQ_PIN 3
#define DEFAULT_RFM69_IRQ_NUM 1

?
i will try and tell if it works. thankyou