Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

💬 NRF52 Gateway -(RFM69-option)

openhardware.io last edited by openhardware.io

https://www.openhardware.io/view/575/NRF52-Gateway-RFM69-option
Reply Quote 0
1 Reply Last reply
canossa last edited by

Hey, after some months what's your opinion abouts the gateway?
You still prefer the nrf52 instead of the rfm69?
Reply Quote 0
1 Reply Last reply
Omemanti last edited by @canossa

@canossa Sorry for the late response.

yeah, since is so compact and you can get it for relatively cheap I opted in for the NRF52.

For home automation, I merged MySensors with Domoticz and it works for months now.
https://forum.mysensors.org/topic/7836/what-did-you-build-today-pictures/738
Reply Quote 0
1 Reply Last reply

gateway 101 rfm69 60 nrf52832 22 e73-2g4m04s 4 ebyte 2

3
Posts

1991
Views

Log in to reply

Suggested Topics

💬 MySRaspiGW PA+LNA - MySensors Raspberry Pi GPIO Gateway
OpenHardware.io • gateway nrf24l01 raspberry smd gpio pa+lna • • openhardware.io

10

0
Votes

10
Posts

3648
Views

@EddyG PCB received and tested, new version (v1.1) available here and on github.
Pi 4 ethernet gateway with NRF24L01 + PA and LNA & Domoticz
My Project • gateway • • bsmtdweller

17

0
Votes

17
Posts

93
Views

Cool project @bsmtdweller New thread or stay in this doesn't matter much, but for people searching the forum (or their favorite search engine) in the future, I think a new thread with a subject containing "incubator" will be more clear. I would build it with multiple nodes. Smaller chunks of code, easier wiring, easier to isolate individual parts which helps tremendously when troubleshooting, easer to reuse code for one node in case you (or someone else) want to expand the project later, easier to remove a part if you (or someone else) don't need it. The non-mysensors code is more important, so I would start with that, but make sure all parameters that you want to be able to change are stored in variables and not hardcoded. Then add the MySensors code to update the values of the variables. The autonomy will be hard. Normally I would prefer to have all logic in the controller, since a controller has much better ways to program and debug stuff. Not fun to write - and maintain - in C with very rudamentary debugging tools. But as you say, being reliant on having Domoticz working all the time might not be good. Having the system fail gracefully will be a challenge. A start could be to search the forum for MY_TRANSPORT_WAIT_READY_MS to see what others have done. And maybe - to make the system as reliable as possible - you should add everything to a single node instead of splitting it up into multiple nodes.
all the gear, no idea
General Discussion • gateway vera help newbie • • baldsi

10

0
Votes

10
Posts

4663
Views

@maltimus - thanks, I can see the picture. frstratingly I have the Vera Edge though!
Newbie question about Sending sensor data with an nRF52832 module to my sensors
Hardware • gateway • • tBS

11

1
Votes

11
Posts

100
Views

@tBS You should try the low power sketches by @NeverDie or @berkseo - They are available on openhardware.io
Boards manager package does not install Sensebender gateway
Troubleshooting • gateway sensebender • • billgoolsby

1

0
Votes

1
Posts

786
Views

No one has replied
ESP8266MQTTClientGateway
Bug Reports • gateway mqtt esp8266 • • mbj

8

0
Votes

8
Posts

2872
Views

@hek That was very visible, please excuse my ignorance. Even though I have looked at this page I managed to leave the change unnoticed.
Is there a Gateway connection timeout?
General Discussion • gateway • • A3V

2

0
Votes

2
Posts

32
Views

@A3V such a feature would definitely make sense now that gateways can have local sensors. But no-one has added it unfortunately. A solution could be to use the code at https://github.com/mysensors/MySensors/blob/2e00bf6a10f76d6aaa1999e12313237bc3edabd3/core/MyTransport.cpp#L446 as inspiration and do something similar at https://github.com/mysensors/MySensors/blob/2e00bf6a10f76d6aaa1999e12313237bc3edabd3/core/MyGatewayTransportEthernet.cpp#L175

21
Online

11.6k
Users

11.2k
Topics

113.0k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1