Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

any can help me? arduino code for washing machine stop when overload using weight sensor

Cin last edited by

any can help me? arduino code for washing machine stop when overload using weight sensor
Reply Quote 0
1 Reply Last reply
Tmaster last edited by Tmaster

what is a weight sensor,and where you put this?

There are weight overload in a washing machine? my machine only stops if the weight is not centered, because it start to jumping
Reply Quote 0
1 Reply Last reply
RJ_Make Hero Member last edited by

I think a vibration sensor may work better in this case, and there are examples.
Reply Quote 0
1 Reply Last reply

3
Posts

1744
Views

Log in to reply

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
Getting Better Range with NRF24L01 Modules
My Project • • MasonBlake

6

0
Votes

6
Posts

45
Views

Thank you so much for your support
Interface-board-for-remote-control
My Project • • OldSurferDude

2

1
Votes

2
Posts

25
Views

That is a well documented project. Much appreciated
Need help with Code. Simple Nod with 4 button's and 2 Led output. Cant get he Led to work as I whant. They respond but both lights
My Project • mysensors • • Knightan

2

0
Votes

2
Posts

10
Views

@Knightan I believe that your problem may be related to this block of code. See my thoughts as comments.... if (message.type == V_STATUS) { //This is true for all messages received // Change relay state state_1 = message.getBool(); //This sets state for state_1 to the received value. digitalWrite(LED_PIN_Channel_1, state_1?RELAY_1_ON:RELAY_1_OFF); // Store state in eeprom saveState(CHILD_ID_5, state_1); // Write some debug info Serial.print("Incoming change for sensor: STATE 1"); Serial.print(message.sensor); Serial.print(", New status: "); Serial.println(message.getBool()); } if (message.type == V_STATUS) { // Change relay state state_2 = message.getBool(); //This sets state for state_2 to the received value. digitalWrite(LED_PIN_Channel_2, state_2?RELAY_2_ON:RELAY_2_OFF); // Store state in eeprom saveState(CHILD_ID_6, state_2); // Write some debug info Serial.print("Incoming change for sensor: STATE 2"); Serial.print(message.sensor); Serial.print(", New status: "); Serial.println(message.getBool()); } It seems to me that state_1 = message.getBool(); AND state_2 = message.getBool(). So they both get set to the incoming value. I think you need to not set both to the same value and instead differentiate them to unique values. I could be wrong as I have not had chance to do anything related to mysensors for a long time now - I also don't use Domoticz. Have a look at the code on this page, it might help you a lot.... https://www.mysensors.org/build/relay
Soil Moisture Sensor Powered by solar charged battery
My Project • battery home assistant low power eeprom solar calibration • • OldSurferDude

5

1
Votes

5
Posts

40
Views

@OldSurferDude I use this. https://www.homedepot.com/p/Orbit-Solenoid-for-Battery-Operated-Timer-57861/203151515 Instead of having to hold the valve open, i can just pulse it. I use a simple motor controller to pulse it and when i need to close it, pulse it in "reverse". That way I could use a battery and if it only opens once or twice a day it's only a half a second or so of draw off the battery.
BT832X PA / LNA
My Project • • nagelc

1

0
Votes

1
Posts

13
Views

No one has replied

16
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1