💬 jModule

[tjay4x4]

@aproxx said:

Any chance you will be creating a 'panelized' version of this board? With these small sizes 4 boards can be fitted on a 5 by 5cm board, while still keeping the same price. I'd be happy to order a few if that's available!

I'm just order it, on Dirtyboard not tested yet. Maybe this what you need?
http://dirtypcbs.com/view.php?share=18851&accesskey=01fcfdedf25cb9105e13f2d50d9ea385

[alexsh1]

Nice one!
I really would like to see the version of it for nrf24l01+ SMD

[ted]

Very nice. The only downside I can think of is that AMS1117 is power hungry. Is there a pin compatible regulator with uA level standby current?

[julisses]

@ted
I do not care about the power. I use USB wall charger to power my nodes. I can recommend this model (it is almost the size of jModule after removing the case):
http://www.aliexpress.com/item/1pc-High-Quality-5V-1A-EU-Plug-AC-Travel-USB-Wall-Charger-for-iPod-for-iPhone/32581266560.html?spm=2114.30010308.3.299.EEQVE8&ws_ab_test=searchweb201556_6,searchweb201602_5_10017_10005_10006_10034_10021_507_10022_9026_10020_10018_10019,searchweb201603_2&btsid=7f600ac6-6e52-41b9-9da5-5c4379d7a639

[ted]

I modified the design to use a XC6206 serial LDO (1uA standby current). I placed an order with dirtypcb. You can find the design here: http://dirtypcbs.com/view.php?share=19651&accesskey=2e5e31a83bf6fe21510c3bc438e12df7

Will update when I get the board on hand.

[m26872]

@julisses Would you mind posting a photo of what that supply looks like inside? Preferably to this thread: http://forum.mysensors.org/topic/2477/are-chinese-power-supply-chargers-that-dangerous-to-use

[julisses]

@m26872

Unsolder USB connector and instead of the connector use wires to connect the jModule.

[sundberg84]

@julisses - Be carefull...
More info here: http://forum.mysensors.org/topic/1607/safe-in-wall-ac-to-dc-transformers/ and as @m26872 said: http://forum.mysensors.org/topic/2477/are-chinese-power-supply-chargers-that-dangerous-to-use

I have a couple of those cheap power supplies running some nodes and they tend to give up after some time as well...
If you look after them thats fine... but im not to comfident with those cheap usb power supplies any more.
Just a tip - as I said, have some working fine but be careful.

[Cliff Karlsson]

Do you have a link for the angular pin-header? I noticed after soldering everything and could not get the arduino/jModule together that the angular pinheaders have the plastic in the other way. I tried with a new and just turned the pinheaders in the other way, but then the exposed pins got too short, same result when prying of every pin and turning them around manually.

[cvanandel]

I had the same problem, I straightened out a set of angular headers, then soldered them into the board, and bend them at the place I needed.
Not the best solution, but I had to many standard angular pins to go and buy more.

[hek]

http://www.ebay.com/itm/10pcs-90-Degree-Bent-Right-Angle-Pin-Header-Breakable-40pin-Single-Strip-2-54mm-/231215719944?hash=item35d587e608:g:cHwAAOSw3ydV2ZCV

[NeverDie]

Nice work!

Is there some kind of female plug that could be used instead? It's nicely compact--except for the male pins sticking out.

[NeverDie]

Regardless, I just now ordered some. Thanks!

[NeverDie]

OK, I "get it" now. The male pins that are sticking out are entirely optional.

[alexsh1]

Did anyone do any power consumption tests on these? I cannot get it below 1.5mA. I think I need to mod my Pro Mini and remove the LED and the regulator.

[ted]

@alexsh1
The regulator on the board (AMS1117) consumes several mA at idle. You may need to find an alternative that has uA level quiescent current. I modified the board to use a XC6206 serial LDO (1uA standby current, see my previous post). I have the board manufactured by dirtypcb and have made sensors. Will test the battery life soon.

[alexsh1]

@ted thanks for your prompt reply. I do not have AMS1117 as I'm running Arduino Pro Mini 3.3V. I figured out it was the Mini itself. I had to remove the onboard regulator and the LED and right now my consumption is 6uA.
I'm moving away from 5V boards as I think these will be phased out eventually.

Good point on AMS1117 - this is not a battery friendly regulator

[Nca78]

@ted said:

I modified the design to use a XC6206 serial LDO (1uA standby current). I placed an order with dirtypcb. You can find the design here: http://dirtypcbs.com/view.php?share=19651&accesskey=2e5e31a83bf6fe21510c3bc438e12df7

Will update when I get the board on hand.

Hello @ted, thank you for the link on dirtyPCB, I just ordered some boards. Do you have any feedback related to battery life when running at 5V ?

[Nca78]

@AWI said:

@Qu3Uk I can confirm (from measuring a sample) that the large pad is not connected to anything.

However :smirk: it is hard to beat the price of an AMS1117

Thank you very much for the link, I was about to buy less units for a higher price for another board, then I remembered about seeing a link with very cheap price on this thread :)

[cimba007]

Doh .. I just blindly orded this board but after checking the eagle layout .. could it be that your power wiring is messed up? The AMS1117 is chained behind the ProMini LDO which I guess is very weak. Would it be much better to put the raw-input on the jModule, power the NRF24 with the AMS1117 output and the pro mini?