Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

💬 Ebyte nRF52832 Prototyping Board

openhardware.io last edited by openhardware.io

https://www.openhardware.io/view/472/Ebyte-nRF52832-Prototyping-Board
Reply Quote 0
1 Reply Last reply
NeverDie Hero Member last edited by NeverDie

I suppose panelizing this board together with a pure prototype board might achieve the objective I was aiming for....
Reply Quote 0
1 Reply Last reply
NeverDie Hero Member last edited by

It works. Project completed.
Reply Quote 2
1 Reply Last reply
NeverDie Hero Member last edited by

I recommend snipping off the DTR pin using flush cutters. Given the current configuration, it isn't going to work properly.
Reply Quote 0
1 Reply Last reply
ahmedadelhosni last edited by

Can you please propose what type of inductors and capacitors did you use ?
A BOM will be great.

Actually I am asking because I knew there is something called SRF from this topic https://devzone.nordicsemi.com/question/171472/filter-inductor-requirement-for-nrf52832-in-dcdc-mode/

Thanks.
Reply Quote 0
1 Reply Last reply
NeverDie Hero Member last edited by @ahmedadelhosni

@ahmedadelhosni said in Ebyte nRF52832 Prototyping Board:

Can you please propose what type of inductors and capacitors did you use ?
A BOM will be great.

It is exactly the same BOM as this: https://www.openhardware.io/view/471/Ebyte-nRF52832-Small-Breakout-Board#tabs-bom
Reply Quote 0
1 Reply Last reply
ahmedadelhosni last edited by @NeverDie

@NeverDie thanks
Reply Quote 0
1 Reply Last reply

7
Posts

1896
Views

Log in to reply

Suggested Topics

💬 MyGateway
OpenHardware.io • mysensors gateway rfm69 ethernet poe • • openhardware.io

10

0
Votes

10
Posts

152
Views

Oh, I never even thought of that as a possibility. I really like KiCad, and it's my preference. For a while I had Eagle for work, but even then I still preferred KiCad whenever I was given a choice.
💬 air quality motherboard for sensor.community project
OpenHardware.io • sensor.community luftdaten dust sensor • • openhardware.io

1

0
Votes

1
Posts

10
Views

No one has replied
💬 In-wall scene controller OLED keypad
OpenHardware.io • mysensors scene controller wall switch oled display keypad • • openhardware.io

7

0
Votes

7
Posts

2050
Views

@Michael-Link I have been out of touch with MySensors for some time now and looking to slowly get back into it. I created this and a few other boards back in 2018 All of the GERBER files for this are in the "Design Files" tab. Those you should be able to send to JLC PCB or one of the other fab houses and have some made. This was designed to be used with 2 other boards that I designed. There was the processor board and the power supply board. The processor board was designed in a way that I could use a couple different switch boards. This one and a universal multi-switch board that had multiple configurations. If you look here you will see my other boards.
💬 HLK-PM01 breakout board
OpenHardware.io • hlk-pm01 • • openhardware.io

38

0
Votes

38
Posts

5408
Views

what the ratings are of the two capacitors used in your circuit? A 1000 uF and a 100 uF?
💬 AC-DC double solid state relay module
OpenHardware.io • light hlk-pm01 acdc light switch solid state relay • • openhardware.io

226

7
Votes

226
Posts

103501
Views

What I didn't quite figure out was how it operates independently as a regular light switch. What I find most interesting is that this is 8 years old. There have been some incredible advances in the IoT world in that time. I was about to do a similar thing which morphed into an ESP-12F then added a touch screen. I call it the Universal Light Switch Imagine this: All the switches are identical. Any switch can easily be configured to control up to five devices ... and then changed, on-the-fly, to control a different set of devices. My design is part of a system that would require a controller (eg. Home Assistant), an MQTT broker, and receiving modules in the devices being switched. It's WiFI which assumes an access point. The DIY ULS is under $20 and the off-the-shelf receiving modules are under $10. (About the cost of a non-networked dimmer switch) If one doesn't have the controller and MQTT broker, they can run on an old (5 years?) computer (which is cheaper than an old RasberryPi). This project is a good one! OSD

36
Online

11.6k
Users

11.2k
Topics

112.9k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1