Topics created by raptorjr

@raptorjr said in Glowing/pulsing yellow LED?: MKRNB 1500 It helps if you post a wiring diagram and a sketch.

@yveaux In my outdoor tempsensor everything was working for a while. And to avoid any problems with the initial setup I put a Nano on a breadboard with only the nrf24 connected. The first setup could have had some issues that I don’t know of, but strange that my test setup have the same problems? That should have avoided any hidden problems to test everything again in a new setup. And Arduino runs on 5V and nrf24 on 3.3V. Is there any other way to check the function of a nrf24? Maybe some other sketch that is not mysensor but able to verify the nrf24 works. I need to try to narrow down the problem because it seems strange that all 4 are broken.

@raptorjr If you can figure out what the filter differential pressure should be when requiring serviced (perhaps from the filter manufacturer or a manual?), it should be possible to find a pressure switch which triggers alarm on the supply side of the filter. If I recall correctly, some water supply pump pressure switch controllers can be turned down to trigger between 5 and 30 psi, perhaps an old one can be found and re-purposed if it fits the range you are aiming for, however fugly they are...

You may need to look at influxdb and grafana to do the reports you are looking for

@ninkasi @raptorjr Consider the use of resQ tape. Not sure if this is available world-wide, but the use of it is very versatile. I've used heat shrink with and without the glue layer inside. Works for some time, but water gets in. Only the resQ tape has proven to keep the joints (cable entries of the connectors) watertight! See this video: ResQ-tape EN Self fusing silicone tape – 02:21— AGROCENTER BR, Boozz

@bjacobse Thank you for the links.

@raptorjr said in Communication problem or?: A 47uF tantalum capacitor worked. That is good news! The node started as a prototype with the plan to make it properly when I saw it >was working. But it is more fun to do something new, at least when the node is >working. I know all about how that one goes, at least it is not just me!

@mfalkvidd Thank you. Then there should be no problem.

@raptorjr Visual Studio uses libraries from Arduino ide, so the only way to get updates is through the Arduino ide unless you install libraries manually. So it's a good thing to open Arduino ide every now and then if you want updates

@AWI This is what I get with debug turned on: Temperature=25.10, LastTemp=25.10 Flow rate: 0.0L/min Output Liquid Quantity: 0.00L Temperature=25.00, LastTemp=25.10 TSF:MSG:SEND,1-1-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:25.0 Flow rate: 0.0L/min Output Liquid Quantity: 0.00L TSF:MSG:READ,0-0-1,s=2,c=1,t=2,pt=0,l=1,sg=0:0 TSF:MSG:ACK REQ TSF:MSG:SEND,1-1-0-0,s=2,c=1,t=2,pt=0,l=1,sg=0,ft=0,st=OK:0 Incoming change for sensor:2, New status: 0 Temperature=25.10, LastTemp=25.00 !TSF:MSG:SEND,1-1-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=NACK:25.1 Flow rate: 0.0L/min Output Liquid Quantity: 0.00L Temperature=25.10, LastTemp=25.10 Flow rate: 0.0L/min Output Liquid Quantity: 0.00L

Added a HomeGenie page on the main site: https://www.mysensors.org/controller/homegenie

Well, I cant seem to find a solution to getting the total water volume from my sensor to Domoticz. Thinking about Plan B, is it possible to get the virtual dimmer percentage back to my node? Then I could do the comparison there, where I have total water volume.

Hello @TheoL I am having the same problem with a slightly similar sketch. the delay didn't have much impart. One second its working fine and the next its breaking into errors. I couldn't find a .1uf Capacitor, so I used electrolytic 1uf instead. Worked fine in the Sprinkler Project, but I don't know if that's the problem here. My sketch is a follows:- // Example sketch showing how to control physical relays. // This example will remember relay state even after power failure. // Enable debug prints #define MY_DEBUG // Enable and select radio type attached #define MY_RADIO_NRF24 #define MY_NODE_ID 6 // Set this to fix your Radio ID or use AUTO or 1 #define MY_REGISTRATION_FEATURE // Forece registration #define MY_REGISTRATION_RETRIES 5 #include <Wire.h> #include <TimeLib.h> #include <SPI.h> #include <MySensors.h> #include <LCD.h> #include <LiquidCrystal.h> #include <LiquidCrystal_I2C.h> // For Debug #ifdef DEBUG_ON #define DEBUG_PRINT(x) Serial.print(x) #define DEBUG_PRINTLN(x) Serial.println(x) #else #define DEBUG_PRINT(x) #define DEBUG_PRINTLN(x) #define SERIAL_START(x) #endif #define RELAY_PIN 2 // Arduino Digital I/O pin number for first relay (second on pin+1 etc) #define NUMBER_OF_RELAYS 4 // Total number of attached relays #define RELAY_ON 0 // GPIO value to write to turn on attached relay #define RELAY_OFF 1 // GPIO value to write to turn off attached relay #define SKETCH_NAME "Swimming Pool Node" #define SKETCH_VERSION "0.1.4" #define CHILD_ID 0 MyMessage msg(1,V_LIGHT); unsigned long SLEEP_TIME = 5000; // Sleep time inbetween reads in milliseconds void setup() { for (int sensor=1, pin=RELAY_PIN; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) { // Then set relay pins in output mode pinMode(pin, OUTPUT); // Set relay to last known state (using eeprom storage) // digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF); // to remember last state digitalWrite(pin, loadState? 0 : 0); // Keep everything off after power failure } } void presentation() { sendSketchInfo(SKETCH_NAME, SKETCH_VERSION); // Fetch relay status for (int sensor=1, pin=RELAY_PIN; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) { // Register all sensors to gw (they will be created as child devices) present(sensor, S_BINARY); pinMode(pin, OUTPUT); // Then set relay pins in output mode // boolean savedState = loadState(sensor); // Set relay to last known state (using eeprom storage) // digitalWrite(pin, savedState?RELAY_ON:RELAY_OFF); // send(msg.set(savedState? 0 : 1)); } DEBUG_PRINTLN(F("Sensor Presentation Complete")); } void loop() { // Alway process incoming messages whenever possible // Sleep until interrupt comes in on motion sensor. Send update every two minute. // sleep(digitalPinToInterrupt(msg.sensor-1+RELAY_PIN), CHANGE, SLEEP_TIME); wait(SLEEP_TIME); } void receive(const MyMessage &message){ // Change relay state if message is receieved if (message.type == V_STATUS){ digitalWrite(message.sensor-1+RELAY_PIN, message.getBool()?RELAY_ON:RELAY_OFF); // Store state in eeprom saveState(message.sensor-1+RELAY_PIN, message.getBool()); // Write some debug info Serial.print("Incoming change for sensor ID: "); Serial.print(message.sensor); Serial.print(", New status: "); Serial.println(message.getBool()); } }

Beer from you.

Don't know what I did wrong, but I didn't get the latest git version. I guess I somehow downloaded 2.0 again. But after some investigation I got the latest version and everything seems to be working now Thank you for your help.

I found the link to the updated 2.0 sketch and even though I still have problems, this is not one of them anymore https://github.com/mysensors/MySensorsArduinoExamples

@scalz said: I just would like to confirm that esp8266(nodemcu in my case) mqtt client gw works ok with rfm69 Thanks for the confirmation!