My Relay Module



  • I started a project with Mysensors to automate some parts of my home, I made the first gateway with Arduino and an ethernet shield.

    My goal was to have a 220V controlled by Vera Lite.

    What you need:
    -Arduino Nano
    -Radio module NRF24L01 +
    -capacitors
    -resistances
    -breadboard thousand holes
    -Relay Module 10A
    -cables and plugs

    The wiring diagram.
    collegamenti-con-bottone-e1420805157407.png

    is important to the condensoatore of VCC and GND of the radio to the stability and the good reception of the same.

    Here's my self-built PCB
    2015-01-08-18.45.55-e1420805330292.jpg

    2015-01-08-18.46.41-e1420805419401.jpg

    2015-01-08-18.46.20-e1420805491322.jpg

    we put it all in a box of Gewiss 8cm x 12 cm
    2015-01-08-19.15.10-e1420805637459.jpg

    We insert the power supply
    2015-01-08-19.38.54-e1420805788700.jpg

    finally finished work:
    2015-01-08-21.34.48-e1420805899319.jpg

    Vera display
    Immagine-e1420806830432.png

    Link code

    Thanks to All



  • Very nice write up! Next add some current sensing ability to see what your load is pulling. ๐Ÿ™‚ Although if used for lighting, mostly negligible I suppose haha.


  • Admin

    Nice setup @gigi!



  • @NotYetRated said:

    Very nice write up! Next add some current sensing ability to see what your load is pulling. ๐Ÿ™‚

    A non invasive sensor would be ideal. I alredy use energimonitor for solar panels!!!!!



  • Bello GiGi! Nice GiGi.

    If you want pm me as I understand we are from the same country.
    May be we can exchange some experience in italian ๐Ÿ˜‰
    Will copy your design





  • if we put this box in wall then power supply will safe or not?

    5v power supply adapter's temperature will afact or not?



  • any one care to confirm whats happening with the AC wires in this? i cant quite make it out from the photos



  • Hello everyone , I have a problem . maybe it's stupid , I have a server with raspberry domoticz , I downloaded code, but by the following errorCattura.PNG


  • Admin

    You seem to have downloaded the development branch of the MySensors library. The code you're trying to run is 1.5.



  • I downloaded this , https://github.com/mysensors/Arduino . I Submitted libraries entirely within the zip file in my briefcase Arduino library.
    however it from the library is the 1.5 readme. Where am I wrong ?
    il codice รจ il seguente

    #include <MySensor.h>
    
    #include <SPI.h>
    #include <Bounce2.h>
    
    #define RELAY_PIN 4 // Arduino Digital I/O pin number for relay
    #define BUTTON_PIN 3 // Arduino Digital I/O pin number for button
    #define CHILD_ID 1 // Id of the sensor child
    #define RELAY_ON 1
    #define RELAY_OFF 0
    
    Bounce debouncer = Bounce();
    int oldValue=0;
    bool state;
    MySensor gw;
    MyMessage msg(CHILD_ID,V_LIGHT);
    
    void setup()
    {
    gw.begin(incomingMessage, AUTO, true);
    
    // Send the sketch version information to the gateway and Controller
    gw.sendSketchInfo("Relay & Button", "1.0");
    
    // Setup the button
    pinMode(BUTTON_PIN,INPUT);
    // Activate internal pull-up
    digitalWrite(BUTTON_PIN,HIGH);
    
    // After setting up the button, setup debouncer
    debouncer.attach(BUTTON_PIN);
    debouncer.interval(5);
    
    // Register all sensors to gw (they will be created as child devices)
    gw.present(CHILD_ID, S_LIGHT);
    
    // Make sure relays are off when starting up
    digitalWrite(RELAY_PIN, RELAY_OFF);
    // Then set relay pins in output mode
    pinMode(RELAY_PIN, OUTPUT);
    
    // Set relay to last known state (using eeprom storage)
    state = gw.loadState(CHILD_ID);
    digitalWrite(RELAY_PIN, state?RELAY_ON:RELAY_OFF);
    }
    /*
    * Example on how to asynchronously check for new messages from gw
    */
    void loop()
    {
    gw.process();
    debouncer.update();
    // Get the update value
    int value = debouncer.read();
    if (value != oldValue && value==0) {
    gw.send(msg.set(state?false:true), true); // Send new state and request ack back
    }
    oldValue = value;
    }
    
    void incomingMessage(const MyMessage &message) {
    // We only expect one type of message from controller. But we better check anyway.
    if (message.isAck()) {
    Serial.println("This is an ack from gateway");
    }
    
    if (message.type == V_LIGHT) {
    // Change relay state
    state = message.getBool();
    digitalWrite(RELAY_PIN, state?RELAY_ON:RELAY_OFF);
    // Store state in eeprom
    gw.saveState(CHILD_ID, state);
    
    // Write some debug info
    Serial.print("Incoming change for sensor:");
    Serial.print(message.sensor);
    Serial.print(", New status: ");
    Serial.println(message.getBool());
    }
    }```

  • Admin



  • thank you! I apologize for my level , I hope to fix with your help.



  • Here is the improved code that I used on my Arduino Mega to create a home automation controller

    New optimized code to arduino mega

    https://codebender.cc/sketch:206446



  • Update: Forget it, the code works with Arduino Mini and 2 relay. I tried one after the code of Arduino Mega and not working. Something wrong but I do not know what I require help
    picture.jpg

    I found mistakes on Arduino Mega solvable at the following link
    http://forum.mysensors.org/topic/2161/the-mysensor-1-5-code-is-not-compiling-for-my-arduino-mega-2560-board/1
    but I do not have this kind of problem you can get support? I connected NRF24L01 to Arduino Mega, as if it were an Arduino Nano, right?


  • Admin

    The SPI pins has different pin numbers on the Mega.

    Here is an example that runs the the Mega:
    http://www.mysensors.org/build/scene_controller



  • I connected the radio module as follows

    AtMega 2650 Arduino Step Down Module/Radio
    GND > GND
    5V > Step Down module VCC
    14 > SCK
    15 > MOSI
    16 > MISO
    17 > CE
    18 > CSN
    I tried but it did not work I tried to connect also IrQ
    2 > IRQ
    it did not work. I tried to connect to 3v3 with the capacitor. it did not work. I tried adding the line in the code
    #include <MyTransportNRF24.h>
    #include <MyHwATMega328.h>
    but to no avail. I am groping in the dark


  • Admin

    You haven't said what problem you experience. Logs or anything else...



  • I have "check wires" error on the serial arduino....
    where do I fit in debug mode there is a guide?
    I saw a video that uses MQTT program on mac.
    I have downloaded windows MYSController I can be of help? How do I connect my PC? It is all new and are a little confused. ๐Ÿ˜ต ๐Ÿˆณ

    I "atmega adk" is a problem?
    https://www.arduino.cc/en/uploads/Main/ArduinoADK_R3_Front_450px.jpg



  • Have you defined using softspi since using those pins?

    I'm using different pins with mega and everything started to work after adding capacitor to radio:
    GND > GND
    3.3 > VCC
    52 > SCK
    51 > MOSI
    50 > MISO
    9 > CE
    10 > CSN
    2 > IRQ



  • soon as I finish the project it will create a new post in the category myproject
    @pjr unfortunately I read your seat now but I confirm that pins are those that use exact thank - @salvato that helped me as an angel.

    the irq pin does not need to be connected


Log in to reply
 

Suggested Topics

40
Online

11.4k
Users

11.1k
Topics

112.6k
Posts