RelayWithButtonActuator (6 channel)

vampircik

PARTS LIST:

Relays (6 channel)
NRF24L01 Radio
Arduino Pro Mini
Push button (6)
Shift Register (SN74HC595)

Hello. Help make this project. I need to control 6 groups of 6 through the controller and buttons that are on the device. I neselen writing sketch. what people can help.
needs a sketch and a description of how to collect it. I need to control the lighting in the street like a phone and pressing locally on the device itself.
willing to pay for it, if necessary.

vampircik

устройство.jpg платка в сборе.jpg платка травление.jpg

BartE

@vampircik i can help writing a sketch, but what exactly do you want to achieve .

Just a 6 times on/off button operated relays?
and why adding the shift register the Pro mini should have enough I/O pins?

But can you send met the exact wiring diagram, than i can give it a try.

vampircik

you did not understand. in the scheme will be 6 switches and relays 6. all these controls one Arduino.

@BartE said:

i can help writing a sketch, but what exactly do you want to achieve .

Just a 6 times on/off button operated relays?
and why adding the shift register the Pro mini should have enough I/O pins?
But can you send met the exact wiring diagram, than i can give it a try.

vampircik

vampircik

нажали кнопку, включилось реле, потом выключили через телефон это реле. и так в любой последовательности.

vampircik

BartE

@vampircik this code snippet should work.

The switch 1 till 6 should be connected to pin A0, A1, A2, A3, 4 and 5 and should connect to ground.

The SN74HC595 should be connected with:

pin 14 (DS) to Arduino pin 6
pin 12 (LATCH/ST_CP) to Arduino pin 7
pin 8 (CLK/SH_CP) to Arduino pin 11
pin 16 (Vcc) and pin 10 (MR) to + 5 volt
pin 8 (GND) and pin 13 (OE) to ground
relay 1-6 to pin 15 (Q0), 1 (Q1), 2 (Q2), 3 (Q3), 4 (Q4) and 5 (Q4) the other relay pins connected to ground
(note 18/1: fixed pin number error as posted below)

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - Henrik Ekblad
 * Version 1.1 - Bart Eversdijk - 6 switch version with Shift Register (SN74HC595)
 * 
 * DESCRIPTION
 * Example sketch showing how to control physical relays. 
 * This example will remember relay state after power failure.
 * http://www.mysensors.org/build/relay
 */ 

#include <MySigningNone.h>
#include <MyTransportNRF24.h>
#include <MyTransportRFM69.h>
#include <MyHwATMega328.h>
#include <MySensor.h>
#include <Bounce2.h>
#include <SPI.h>
#define MYS_INIT_DELAY 500

#define PIN_SR_DATA      6  // shift register data pin   -- data out - 74HC595 (DS) pin 14 
#define PIN_SR_LATCH     7  // shift register latch pin  -- data out - 74HC595 (RCLK) pin 12 
#define PIN_SR_CLOCK     8  // shift register clock pin  -- data out - 74HC595 (CLK) pin 11

struct SWITCHES {
    byte      currentStatus; 
    int       SwitchPin;   // To which Arduino pin this switch is connected
    Bounce    debouncer;
    MyMessage switchMsg;
};

SWITCHES switches[] = {
          {0, A0, Bounce(), MyMessage(0, V_LIGHT)},    // Arduino pin A0
          {0, A1, Bounce(), MyMessage(1, V_LIGHT)},    // Arduino pin A1
          {0, A2, Bounce(), MyMessage(2, V_LIGHT)},    // Arduino pin A2
          {0, A3, Bounce(), MyMessage(3, V_LIGHT)},    // Arduino pin A3
          {0,  4, Bounce(), MyMessage(4, V_LIGHT)},    // Arduino pin D4
          {0,  5, Bounce(), MyMessage(5, V_LIGHT)}     // Arduino pin D5
        };
#define MAXSWITCHES (sizeof(switches)/sizeof(SWITCHES))


// NRFRF24L01 radio driver (set low transmit power by default) 
MyTransportNRF24 radio(RF24_CE_PIN, RF24_CS_PIN, RF24_PA_LEVEL_GW);  
//MyTransportRFM69 radio;
// Message signing driver (none default)
//MySigningNone signer;
// Select AtMega328 hardware profile
MyHwATMega328 hw;
// Construct MySensors library
MySensor gw(radio, hw);

void setup()  
{   
    // Initialize library and add callback for incoming messages
    gw.begin(incomingMessage, AUTO, true);
    
    // Send the sketch version information to the gateway and Controller
    gw.sendSketchInfo("RelaySix", "1.1");

    // Fetch relay status
    for (int id=0; id < MAXSWITCHES; id++) {
       pinMode(switches[id].SwitchPin, INPUT);
       // Activate internal pull-up
       digitalWrite(switches[id].SwitchPin, HIGH); 
        
       gw.present( id, S_LIGHT );
       delay( MYS_INIT_DELAY );

       // Pull the gateway's current dim level - restore light level upon sendor node power-up
       gw.request( id, V_STATUS );
       delay( MYS_INIT_DELAY );
       
       // After setting up the button, setup debouncer
       switches[id].debouncer.attach(switches[id].SwitchPin);
       switches[id].debouncer.interval(5);
    }
    
    // Set shift register pins
    pinMode(PIN_SR_DATA,     OUTPUT);
    pinMode(PIN_SR_LATCH,    OUTPUT);
    pinMode(PIN_SR_CLOCK,    OUTPUT);
    digitalWrite(PIN_SR_LATCH, HIGH);
    
    // Switch off all relays
    sendRelayValues();
}


void loop() 
{
    // Alway process incoming messages whenever possible
    gw.process();
  
    for (byte id = 0; id < MAXSWITCHES; id++) {
        // Button change detected
        if (switches[id].debouncer.update()) {
           Serial.print (F("Switch #"));
           Serial.print (id);
           Serial.print (F(" to "));
           Serial.println (switches[id].debouncer.read());
           
           // Button release detected toggle relay
           if (!switches[id].debouncer.read()) {
             // Toggle relay status
             switches[id].currentStatus = (switches[id].currentStatus ? 0 : 1);
             
             // Set the actual relay status (all 6 at once)
             sendRelayValues();
             
             // Inform the gateway of the current switch status...
             gw.send(switches[id].switchMsg.set(switches[id].currentStatus));
           }
        }
    }
}

void sendRelayValues() {
    // Actually send the valve bits
    digitalWrite(PIN_SR_LATCH, LOW);

    // Shift out all station bit values
    // from the highest bit to the lowest
    for(int id = 0; id < 8; id++)  {
        digitalWrite(PIN_SR_CLOCK, LOW);
        if (id < MAXSWITCHES) {
          digitalWrite(PIN_SR_DATA, (switches[id].currentStatus > 0 ? HIGH : LOW));
        } else {
          digitalWrite(PIN_SR_DATA, LOW);
        }
        digitalWrite(PIN_SR_CLOCK, HIGH);          
    }
    // Set new data active
    digitalWrite(PIN_SR_LATCH, HIGH);
}

void incomingMessage(const MyMessage &message) {
  if (message.isAck()) {
     Serial.println("This is an ack from gateway");
  }
  
  if (message.type == V_LIGHT) {
     byte id = (message.sensor % MAXSWITCHES);

     // Store new value
     switches[id].currentStatus = message.getBool() ? 1 : 0;
     
     // Set the actual relay status (all 6 at once)
     sendRelayValues();
     
     // Inform the gateway of the current switch status...
     gw.send(switches[id].switchMsg.set(switches[id].currentStatus));
           
     // Write some debug info
     Serial.print("Incoming change for sensor:");
     Serial.print(message.sensor);
     Serial.print(", New status: ");
     Serial.println(message.getBool());
   } 
}

About your "willing to pay" remark in the original post, just make a donation to the MySensors project

vampircik

Thank you. Today I will try. according to the results let you know.

vampircik

@BartE said:

pin 8 (CLK) to Arduino pin 11

pin 16 (Vcc) to + 5 volt

pin 8 (GND) to ground

?
Arduino pin 11 = (GND) ?

vampircik

pin 8 (CLK) to Arduino pin 11
pin 8 (GND) to ground

contrary

vampircik

pin 14 (DS) to Arduino pin 6

relay 1-6 to pin 14 (Qa)

contrary микросхема.png

vampircik

This post is deleted!

vampircik

pin 14 (DS) to Arduino pin 6
pin 8 (CLK) to Arduino pin 11
pin 8 (GND) to ground
relay 1-6 to pin 14 (Qa),
микрик.png

korttoma

Maybe it should be like this:

relay 1-6 to pin 15 (Q0), 1 (Q1), 2 (Q2), 3 (Q3), 4 (Q4) and 5 (Q5)

vampircik

pin 8 (CLK) to Arduino pin 11

and with the contact what to do?

vampircik

Arduino pin 11 = MOSI NRF24

vampircik

it seems to me must be so connected. except for the screen?

korttoma

@vampircik said:

pin 8 (CLK) to Arduino pin 11

and with the contact what to do?

Looking att the code @BartE posted it seems like it was supposed to be

pin 11 (CLK) to Arduino pin 8

vampircik

ok try. ...............

korttoma

So the correct instructions should have been:

pin 14 (DS) to Arduino pin 6
pin 12 (RCLK) to Arduino pin 7
pin 11 (CLK) to Arduino pin 8
pin 16 (Vcc) to + 5 volt
pin 8 (GND) to ground

relay 1-6 to pin 15 (Q0), 1 (Q1), 2 (Q2), 3 (Q3), 4 (Q4) and 5 (Q5) the other relay pins connected to ground

Please @BartE correct me if I'm wrong since I have no personal experience from this kind of setup.

vampircik

collected is not working. the controller displays the switch, but it does not control the Arduino.

vampircik

includes buttons, it is displayed on the controller, with only relay nothing happens

vampircik

korttoma

Do you get anything in the serial monitor for your Relay Node?

vampircik

send: 18-18-0-0 s=255,c=0,t=18,pt=0,l=3,sg=0,st=ok:1.5
send: 18-18-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
read: 0-0-18 s=255,c=3,t=6,pt=0,l=1,sg=0:M
repeater started, id=18, parent=0, distance=1
send: 18-18-0-0 s=255,c=3,t=11,pt=0,l=8,sg=0,st=ok:RelaySix
send: 18-18-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.1
send: 18-18-0-0 s=0,c=0,t=3,pt=0,l=0,sg=0,st=ok:
send: 18-18-0-0 s=0,c=2,t=2,pt=0,l=0,sg=0,st=ok:
send: 18-18-0-0 s=1,c=0,t=3,pt=0,l=0,sg=0,st=ok:
send: 18-18-0-0 s=1,c=2,t=2,pt=0,l=0,sg=0,st=ok:
send: 18-18-0-0 s=2,c=0,t=3,pt=0,l=0,sg=0,st=ok:
send: 18-18-0-0 s=2,c=2,t=2,pt=0,l=0,sg=0,st=ok:
send: 18-18-0-0 s=3,c=0,t=3,pt=0,l=0,sg=0,st=fail:
send: 18-18-0-0 s=3,c=2,t=2,pt=0,l=0,sg=0,st=fail:
send: 18-18-0-0 s=4,c=0,t=3,pt=0,l=0,sg=0,st=fail:
send: 18-18-0-0 s=4,c=2,t=2,pt=0,l=0,sg=0,st=fail:
send: 18-18-0-0 s=5,c=0,t=3,pt=0,l=0,sg=0,st=fail:
send: 18-18-0-0 s=5,c=2,t=2,pt=0,l=0,sg=0,st=fail:
find parent
send: 18-18-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,st=bc:
read: 0-0-18 s=0,c=1,t=2,pt=0,l=1,sg=0:0
send: 18-18-0-0 s=0,c=1,t=2,pt=1,l=1,sg=0,st=ok:0
Incoming change for sensor:0, New status: 0
read: 0-0-18 s=1,c=1,t=2,pt=0,l=1,sg=0:0
send: 18-18-0-0 s=1,c=1,t=2,pt=1,l=1,sg=0,st=ok:0
Incoming change for sensor:1, New status: 0
read: 0-0-18 s=2,c=1,t=2,pt=0,l=1,sg=0:0
send: 18-18-0-0 s=2,c=1,t=2,pt=1,l=1,sg=0,st=ok:0
Incoming change for sensor:2, New status: 0
read: 0-0-18 s=255,c=3,t=8,pt=1,l=1,sg=0:0
parent=0, d=1
Switch #1 to 1
Switch #2 to 1
Switch #3 to 1
Switch #4 to 1
Switch #5 to 1
Switch #1 to 0
send: 18-18-0-0 s=1,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #1 to 1
Switch #2 to 0
send: 18-18-0-0 s=2,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #2 to 1
Switch #0 to 1
Switch #0 to 0
send: 18-18-0-0 s=0,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #3 to 0
send: 18-18-0-0 s=3,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #3 to 1
Switch #4 to 0
send: 18-18-0-0 s=4,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #4 to 1
Switch #5 to 0
send: 18-18-0-0 s=5,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #5 to 1
Switch #4 to 0
send: 18-18-0-0 s=4,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #4 to 1
Switch #4 to 0
send: 18-18-0-0 s=4,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #4 to 1
Switch #4 to 0
send: 18-18-0-0 s=4,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #4 to 1
Switch #4 to 0
send: 18-18-0-0 s=4,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #4 to 1
Switch #5 to 0
send: 18-18-0-0 s=5,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #5 to 1
Switch #5 to 0
send: 18-18-0-0 s=5,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #5 to 1
Switch #4 to 0
send: 18-18-0-0 s=4,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #4 to 1
Switch #5 to 0
send: 18-18-0-0 s=5,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #5 to 1
Switch #3 to 0
send: 18-18-0-0 s=3,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #3 to 1
Switch #3 to 0
send: 18-18-0-0 s=3,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #3 to 1
Switch #3 to 0
send: 18-18-0-0 s=3,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #3 to 1
Switch #4 to 0
send: 18-18-0-0 s=4,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #4 to 1
Switch #4 to 0
send: 18-18-0-0 s=4,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #4 to 1
Switch #4 to 0
send: 18-18-0-0 s=4,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #4 to 1
Switch #5 to 0
send: 18-18-0-0 s=5,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #5 to 1
Switch #0 to 1
Switch #0 to 0
send: 18-18-0-0 s=0,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #0 to 1
Switch #0 to 0
send: 18-18-0-0 s=0,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #2 to 0
send: 18-18-0-0 s=2,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #2 to 1
Switch #2 to 0
send: 18-18-0-0 s=2,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #2 to 1
Switch #1 to 0
send: 18-18-0-0 s=1,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #1 to 1
Switch #1 to 0
send: 18-18-0-0 s=1,c=1,t=2,pt=1,l=1,sg=0,st=ok:1
Switch #1 to 1

vampircik

this is what I have now happened. includes a button, turn on the relay, reclosing button, there is no result

vampircik

individual libraries should be shipped to the chip?

vampircik

This post is deleted!

BartE

@vampircik i see that with some help from korttoma you manage to find the correct pins setting. @korttoma thx for your help.
korttoma is right about the pin 11, i should have added this link with more background info

The sketch is designed for push buttons and not for toggle switches and will respond when releasing a button press.
In your movie i see that switching on and off via MySensors (mouse clicks) works but the button presses not (always) only switching off.

I found an error in my sketch on line 131

// Store new switch value
switches[id].currentStatus = (switchValue ? 0 : 1);

the correct line should be

// Toggle relay status
switches[id].currentStatus = (switches[id].currentStatus ? 0 : 1);

note: I've updated the sketch in the original post as well

vampircik

BartE Thank you. everything worked.

vampircik

I made my monetary investment. though not particularly large

vampircik

Connect the power supply to the relay which should be governed by the device stops working

RelayWithButtonActuator (6 channel)

Suggested Topics

Welcome
Announcements • • hek

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • • OldSurferDude

Halloween Lights
My Project • led strip light ws2812b • • KevinT

Auxiliary Loads and Mains Charger Controller for my Smart Mobile Home
My Project • • fsgraz

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

RelayWithButtonActuator (6 channel)

Suggested Topics

Welcome Announcements • • hek

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway My Project • • fsgraz

Controlling Blinds.com RF Dooya Motors with Arduino and Vera My Project • • petewill

Water Meter or "How to get Home Assistant to send saved data to an Arduino" My Project • • OldSurferDude

Halloween Lights My Project • led strip light ws2812b • • KevinT

Auxiliary Loads and Mains Charger Controller for my Smart Mobile Home My Project • • fsgraz

0Online

11.4kUsers

11.1kTopics

112.7kPosts

Welcome
Announcements • • hek

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • • OldSurferDude

Halloween Lights
My Project • led strip light ws2812b • • KevinT

Auxiliary Loads and Mains Charger Controller for my Smart Mobile Home
My Project • • fsgraz

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts