I have published all the documentation in a Github repository. If someone wants to make PCBs, I recommend that you wait a little longer until you receive my PCBs and try them.
@shabba
Hi, unfortunately I don't have time and patience for doing BOM's on all of my projects but in this case it's not very hard as the external component count is greatly reduced by using the NRF51822 RF SOC which is a PTR5518 module from Aliexpress. Other than that there is the Microchip touch sense controller - MTCH105 and the usual smd resistors(0603) and caps. Other than that you're not forced to use and solder the onboard dc-dc converter so you don't have to worry about those components - you just need to solder the 3V_EN jumper to use the Livolo 3V output coming from the main relays/power supply board.
Hi!
I have the same problem as terxw. allpcb.com is missing the "NC drill date". Unfortunately I am not able to create this on my own. Can anybody upload this file?
Thanks
@Serg2055 as the name says, openhardware.io is for open hardware.
You are allowed to sell PCB units, partially or fully soldered boards, but selling source is not an acceptable option. Please include readable schematic and source of your boards or at least gerbers or bom. For all your boards posted on openhardware.io.
Thank you !
Hello,
I'm thinking about upgrading this board to include pinout for LIS3DH breakout board, like this one :
https://www.aliexpress.com/item/LIS3DH-Three-Converters-Motion-Accelerometer-Triaxial-Acceleration-Temperature-Sensor-Module-Development-Board-Replace-ADXL345/32840326778.html
and ditch the ADXL shield as it's not a good solution, it has either the ADXL345 which uses too much power, or the ADXL362 which is ultra low power but lacks advanced functionality like tap/double tap detection.
I would like to have feedback of users on this (do it sound useful ?), and also know if anyone uses the SMD footprints on the board, for leds and for reserve capacitors, as it could be a cleaner board without those footprints.
I would make the following changes :
put footprint for LIS3DH accelerometer along the "NModule connector" as it has too many pins to put elsewhere
keep only one I2C footprint on the side, for "GY-49" MAX44009 light sensor breakout board: https://www.aliexpress.com/item/GY-49-MAX44009-Ambient-Light-Sensor-Module-for-Arduino-with-4P-Pin-Header-Module/32828654450.html
temperature/humidity would be via the existing "SMD" footprint, it's not through hole but very easy to solder as it's 2.54mm pad spacing
remove SMD footprints for LED, add footprint for through hole reserve capacitor, keep SMD footprints for reserve capacitors only if I have space for them
shield would be a bit extended to go over the 2 M2 holes in the "power" part of the NModule, so it could be fitted with spacers and nylon screws and have stable/reliable mechanical connection between NModule and Shield. Basically this would be the footprint of the shield :
So in the end it would make one shield to have Temperature/Humidity/Light/Acceleration or Temperature/Humidity/Light/Door.
@toyman said in NModule DC Fan / PWM shield:
Can the FET withstand continious 2A load? I have one meter long 5050 strip
FDD8447L is rated for 15A continuous load. You don't want to try that because it's possible only with a big pad and 2oz copper PCB, but 2A will not be a problem on this board, there's plenty of margin
https://isojed.nl/blog/wp-content/uploads/2013/06/FDD8447L.pdf
@TON-RIJNAARD You need to select the board based on the bootloader you have flashed. Complile the code in Arduino and try burning the hex file using a programmer (USBasp, AVRISP, etc..) if are facing issues with Arduino.
