@jkandasa Brilliant - thank you!!!

Automatic node ID's are now also supported! There is a step-by-step install guide here: https://github.com/tsathishkumar/MySController-rs/issues/30 You can easily run this alongside Domoticz. Burn an image for the Mozilla Gateway onto an SD card. Follow the guide above to install MySController-rs. Install Domoticz at port 8081 and 444 (instead of 8080 and 443, as the Mozilla Gateway is already at those ports). flatsiedatsie created this issue in tsathishkumar/MySController-rs closed Installation on Mozilla Gateway Pi image #30

@jkandasa Great! Thanks for pointing me out. I'll take a look. Regards

Well, sure enough we work on sensors but more related to home automation. Industrial automation requires higher quality stuff and usually the sensor types are different. About other forum start searching "industrial automation forum" there are some coming out, also I bet there are some in your specific country too. Communities are everywhere

i think i finally get it. It is impossible... well the only way to let nodes communicate with each other is when a gateway is available (directly or trough other nodes) when the node is starting up. This forum discussion is explaining me the most.. a solution may be.. transform the node that is always on to an gateway. And use antoher channel.. Sidenode; then you can't tell the controller what the status is. Is there realy no way that this can supported? Node to node comunication without the need of an gateway inside the network? Skipping the registration and just send the message around. perhaps i will dive into the source one day and change the registration behavior. Thanks anyway for the help and the very fast responding.

@jkandasa Thank you for the update. I will use this controller in production in few days. Eactly what I want. For non-msensors devices I Will use node-red as glue !

@wesley Ok sorry i see. Sorry

@hek hi... sorry did not know this would be nice if you could do that... so people can get started with the new stuff !

Ok, I feel pretty dumb not to have thought of it before, but I've found the issue. For the sake of anyone running in the same issue, if you are running an ad blocker, try to disable it first. Looking at the request in Chromium, it said "ERR_BLOCKED_BY_CLIENT" Turning off the ad blocker resulted in a dashboard as you would expect it. Sorry for bothering you for something I should have thought of, and thank you for your support.

isn't it just SEXY ?

Thanks for the feedback. If you have comments, send me an emeil. As for multiplatform, I'm going to rewrite the code in ASP.NET5, once it exits beta status.Theoretically, this will make it possible to run the system on Linux and Mac. I wrote code with the future in mind.

It's been a while since I posted here, but openLuup has continued development and is now a really very capable controller with extensive plug-in compatibility with Vera. Latest version always available from GitHub here https://github.com/akbooer/openLuup

If I was to write something like this right now. I would probably use the MEAN stake. MongoDB Express Angular Node.js With NodeJS and express you can have it do your api then add AngulerJS and Web Sockets to those two and you will have a very resonsive Web based UI. Here is were it gets interesting. Python, C++, or C#. Python works with Nodejs very well. Windows 10 under the hood has some big changes which will make it very interesting for development. The new Windows Universal is really new (it is not even released) and very interesting. I have seen it called Core and Windows IoT. I'm right now toying around with Windows IoT on a Raspberry PI and attempting to create a MySensors gateway. I have had some adventures, and am close to putting it away for now until the next build, but it could be very Interesting. I would set it up to use the Vera http API first and then add support for Z-Wave, MySensors, then Insteon.

@Vladut-Grecu said: That remote had a wireless thingy.. W Indeed it was RF based remote control, but it was for X10 protocol and it wasn't compatible with my existing system. There's somewhat painful way to hook x10 to Vera via Raspberry running Mochad driver, but I'm getting rid of x10 altogether.

@Mickey It is mainly for testing OTA updates (POC).

It sounds perfect ! I ever use noip for my ip camera. What about vocal control from the android app ?

If anyone is interested in trying out the implementation using UDP packets sent to the subnet broadcast address, check out my pull request https://github.com/mysensors/Arduino/pull/66

@davy39 said: up ! Could anyone help me to configure domoticz & mysensors in order to control analog RGB led strip ? Is this option working? Or perhaps a RGBW strip...

Is there any development of this plugin?

@dzairo Can't help you with the project as it's way over my pay grade, but it sounds interesting. Good Luck!

Hi. It's long time .. but standard function is : gw.processRadioMessage(); and I make changes in source code in MyGateway.cpp to this : char MyGateway::processRadioMessage() { char isMessage=0; if (process()) { // A new message was received from one of the sensors isMessage=1; MyMessage message = getLastMessage(); if (mGetCommand(message) == C_PRESENTATION && inclusionMode) { rxBlink(3); } else { rxBlink(1); } // Pass along the message from sensors to serial line serial(message); } checkButtonTriggeredInclusion(); checkInclusionFinished(); return isMessage; } But in new library is not file MyGateway.cpp .. then I don't now .. using is : if (gw.processRadioMessage()==1) {..} regards.. there is possible make easy gateway .. controler .. to control only light for example.. then we don't need external controller .. etc..

So, now I replay with 255:255:3;0;4;1 instead of 255;255;3;0;4;0 and when I get the request 1;10;2;0;3;1.4.1 Yes I think node-id 0 should not be used.

@hek I have two sensors in my network ( temp , Hum ) and motion detection. both working in auto mode and request node id from controller ( raspberry pi ) node via gateway . but unfortunately, reponse code of both nodes get same node id 1. may be bug in sendNextAvailableSensorId() function response. any idea? thanks

@EasyIoT Can you share your implementation for MySensorsDriver?

Hi John, appLog.txt I also tried using datatype string but it doesen't work. Meanwhile I have studies the log files more detailed and found the following behavior: when defining the device skeletal and when updating the derived device (first approx. 25 lines in the log file V_STATUS is declared as string with values 51 resp. 52 as specified in the web interface. The entity is "Modul 433 MHz". Later on, when using the toggle switch in the web interface the value has changed in the decription in the log file (see line 164 or 185) value has been changed to on/off. With this definition it seem that the mysensors-Plugin is feeded has been changed from the specified values. My conclusion is that the change is taking place somewhere outside the mysensors-plugin. By the way, if I change the type to string do I have to use quotation marks in the web interface? Thanks a lot for your support. Martin

Hi all we are working on a new web client for our domotic framework. Here some screenshots It's a WIP so we need any help to complete it. The code is available at https://github.com/freedomotic/fd-vue-webapp/