Hello,
I'm thinking about upgrading this board to include pinout for LIS3DH breakout board, like this one :
https://www.aliexpress.com/item/LIS3DH-Three-Converters-Motion-Accelerometer-Triaxial-Acceleration-Temperature-Sensor-Module-Development-Board-Replace-ADXL345/32840326778.html
and ditch the ADXL shield as it's not a good solution, it has either the ADXL345 which uses too much power, or the ADXL362 which is ultra low power but lacks advanced functionality like tap/double tap detection.
I would like to have feedback of users on this (do it sound useful ?), and also know if anyone uses the SMD footprints on the board, for leds and for reserve capacitors, as it could be a cleaner board without those footprints.
I would make the following changes :
put footprint for LIS3DH accelerometer along the "NModule connector" as it has too many pins to put elsewhere
keep only one I2C footprint on the side, for "GY-49" MAX44009 light sensor breakout board: https://www.aliexpress.com/item/GY-49-MAX44009-Ambient-Light-Sensor-Module-for-Arduino-with-4P-Pin-Header-Module/32828654450.html
temperature/humidity would be via the existing "SMD" footprint, it's not through hole but very easy to solder as it's 2.54mm pad spacing
remove SMD footprints for LED, add footprint for through hole reserve capacitor, keep SMD footprints for reserve capacitors only if I have space for them
shield would be a bit extended to go over the 2 M2 holes in the "power" part of the NModule, so it could be fitted with spacers and nylon screws and have stable/reliable mechanical connection between NModule and Shield. Basically this would be the footprint of the shield :
So in the end it would make one shield to have Temperature/Humidity/Light/Acceleration or Temperature/Humidity/Light/Door.
@krisztian
Hi krisztian,
the singleLED board - as its name suggests - features only one LED output. If you want to have a setup with multiple LED strips you need to design a board with multiple outputs. I have already designed a board with 4 outputs, but I haven't built it.
In terms of software you need to register multiple sensors in your program like this:
#define numCh 4 //the number of outputs
const byte ledPins[] = {9,6,5,3};
byte ledLevel[numCh];
boolean ledDimWay[numCh];
//in the setup function request the dim levels from the gateway
for(byte i=0; i<numCh; i++) request(i, V_DIMMER);
//in the presentation function register multiple lights
for(byte i=0; i<numCh; i++) present(i, S_DIMMER);
//if you receive a signal, you need to check for the sensor id
setLED(message.sensor, requestedLevel);
//to set the LED level (function: setLED) you need to use the sensor id to determine brightness and pin
//Fade LED to set level
int delta = (level - ledLevel[child]) < 0 ? -1 : 1;
//Write to LED
analogWrite(ledPins[child], map(ledLevel[child],0,100,0,255));
I will probably publish the whole code once I have built and tested the 4LED controller (i call it "MySensors rainbowLED")
Hope I could help you
ThetaDev
Oh, I never even thought of that as a possibility.
I really like KiCad, and it's my preference. For a while I had Eagle for work, but even then I still preferred KiCad whenever I was given a choice.
@Samuel235 said:
Just one of many ideas, the possibilties are endless. I'de always go for RGB leds over just white, allows for more customisation while able to still give you the same white as the white leds.
... unless, as in my use case, colors are not needed.
I'm too stingy to pay for the unused dry powder!
I recently build successfully a mysensor node based on an Arduino Uno, a Robolink IR sensor and a Robolink DHT11 sensor. The last two from an Elektor sensor kit ever bought for my son when he was still interested by electronics .
My controller is Home Assistant, so I did a merge of the given MySensors example sketch and the Home Assistant example sketch together with the DHT11 sketch.
The airco is a Samsung one, so in the sketch you will find these defines uncommented. Replace by your airco manufacturer.
People interested in building one, can find my sketch on https://github.com/ericvb/MySensorsArduinoSketches
@ToniA a big thanks for the work to decode all these IR sequences!
