Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

32 I2C Relay

dzairo 29 Apr 2016, 15:34 last edited by dzairo 29 Apr 2016, 15:35

Hi all.
I make small project to controll 32 relay by I2C expander PCF8574 .
In my project are V_LIGHT for relay control and V_TEMP to define if want save relay state to eeprom memory or not .
if S_TEMP is 0 then after reset, all relay are close and clear eeprom memory for relay state , if S_TEMP is 1 then relay state are read from memory .. and save state to memory if change state of relay .

V_LIGHT not define if relay is open or close .. only change state from 1 to 0 , and 0 to 1 .
It's to control light in my house ..
0_1461943989896_RelayI2C.zip

PS: tested in Arduino Nano (china clone CH340 with micro USB ) , nrf24L01+ (PCB antenna) with 1x PFC8574
PPS: Node ID is manualy set to 58 if need change to AUTO

regards.
Reply Quote 1
1 Reply Last reply

1
Posts

1.7k
Views

1 out of 1

Suggested Topics

Relay actuator sketch - auto off function
Development • relay • 5 Dec 2014, 02:45 • niccodemi 11 Sept 2015, 15:27

17

0
Votes

17
Posts

9.2k
Views

11 Sept 2015, 15:27

@Dwalt oh wow.. thanks so much.. i was waiting for you to get back to me but never saw this post.. and i just happened to stumble on it when i was looking to see if you had been back on the forum or not. I'm good with the hardware side of things and can shell script and do windows scripting. but still have not learned this coding yet. i have all the hardware for the 433 stuff. i even got the RF stuff to work (on my RPI2) and sniffed all my codes i could just never get it to work with my arduino stuff. likely the code, so i'm excited to give your code a go. Thanks!
RelayWithButtonActuator - another n00b question
Troubleshooting • relay button actuator • 29 Jan 2015, 20:17 • gadu 1 Feb 2015, 19:04

10

0
Votes

10
Posts

3.3k
Views

1 Feb 2015, 19:04

@gadu String totalProjectSuccess = itWorks + wifeIsHappy;
Sensor reading incorrect data from the controller
Bug Reports • relay openhab message.getbool getbool • 27 Feb 2016, 10:07 • Brian Fernando 27 Feb 2016, 10:07

1

0
Votes

1
Posts

938
Views

No one has replied
Relay with ACS712
Hardware • relay nrf24l01+ • 27 Jan 2015, 15:36 • Dheeraj 30 Jun 2016, 21:18

18

3
Votes

18
Posts

12.1k
Views

30 Jun 2016, 21:18

@Shivanand-Chanderbally I recently finished a node using the acs712 and found it to be very sensitive to nearby magnetic fields. It is best to have it as far away from these as you can.
💬 NModule
OpenHardware.io • mysensors temperature relay humidity light pir nmodule door accelerometer touch milight • 23 May 2017, 14:38 • openhardware.io 10 May 2020, 05:43

89

0
Votes

89
Posts

17.8k
Views

10 May 2020, 05:43

@zmatokan said in NModule: @Nca78 Are you still working on this pcbs? i think it would be great to add a version that supports HiLink 220ac->5dc module on powerboard. No I'm not working on NModules anymore, I have a few old nodes using atmega/nrf24 but I switched to NRF5 for "basic" nodes now, and to ESP32 for more "advanced" stuff. NModule was designed for beginner and simple/riskless use, so I don't think adding high voltage option is a great idea, it's better to use an external power supply and connect the output to the powerboard.
💬 Homini AC Powered Relay (2) Module
OpenHardware.io • mysensors relay contest2017 switch light lighting • 27 Feb 2017, 18:03 • openhardware.io 12 Mar 2017, 15:54

14

1
Votes

14
Posts

4.1k
Views

12 Mar 2017, 15:54

@Samuel235 said in Homini AC Powered Relay (2) Module: OMRON G3MB-202P Okay I'm trying to help you with the fuse component. I found a datasheet for the OMRON G3MB-202P. And there are enoght information to be known for fuse selection. I try to calculate it here (and i will try it with my bad English ). The most important information is the melting integral. The Melting integral has A²s as unit. So this means the maximum current for a time can exists without damaging the device. For further information look at wikipedia. So we need any further information about: the protection which is present before (the typical circuit protection in private houses) the melting integral from the device which we want to protect the maximum voltage the maximum switching current the breaking capacity Inrush current for the switched devices (we can't know) Typical values for an automatic circuit breaker in private houses are: from 25 to 100 A²s 230 V AC 16 A So this protection isn't good enough for our relay. The relay have these values: 230 V AC 2 A maximum switching current I²t value (melting integral): 4 A²s the allowed inrush current over a small time is higher than the melting integral. It is a bit confusing i think, but if we calculate the protection for the given melting integral and it's fine. So we can define the parameters for the client (switching site of this application here) The fuse have to be: I²s value higher or equal than the I²s value from the existing protection rating voltage over 230 V AC rating current 2 A or lower (because 2 A is the maximum at 25 °C, for 40 °C it is about 1.6 A) a maximum switching time of 1 second at 2 A or lower time with higher current but below 4A²s! To calculate use the switching time from the fuse datasheet an multiply it two times with the given current for this switching time. And i think a fast blow fuse would be the best. There are SMD fuses with 10.1 x 3 mm and 250 V AC available. If there is no fuse available with the values above, we could combine multiple fuses. A possible solution could be one bigger fuse for both relays and the ac/dc component. And a smaller fuse for the switching site of the relay and the HLK-PM01. But for this it is important that the circuit have only one input for the hot one (L) of 230 V and one output for each relay. In this case we could reduce the big connectors from 6 to 4. Like (L, N, Relay1, Relay2). And the temperature fuse can work for all components too So the protection for the primary site of the HLK-PM01 is a problem i think. Because the are no information available about the I²s value from HLK-PM01. I hope you can understand my English and could follow my explanation?
💬 RFM69 - 8 relays board
OpenHardware.io • rfm69 relay • 24 Jan 2017, 13:33 • openhardware.io 24 Jan 2017, 13:33

1

0
Votes

1
Posts

895
Views

No one has replied

32 I2C Relay

Suggested Topics

Relay actuator sketch - auto off function
Development • relay • 5 Dec 2014, 02:45 • niccodemi 11 Sept 2015, 15:27

RelayWithButtonActuator - another n00b question
Troubleshooting • relay button actuator • 29 Jan 2015, 20:17 • gadu 1 Feb 2015, 19:04

Sensor reading incorrect data from the controller
Bug Reports • relay openhab message.getbool getbool • 27 Feb 2016, 10:07 • Brian Fernando 27 Feb 2016, 10:07

Relay with ACS712
Hardware • relay nrf24l01+ • 27 Jan 2015, 15:36 • Dheeraj 30 Jun 2016, 21:18

💬 NModule
OpenHardware.io • mysensors temperature relay humidity light pir nmodule door accelerometer touch milight • 23 May 2017, 14:38 • openhardware.io 10 May 2020, 05:43

💬 Homini AC Powered Relay (2) Module
OpenHardware.io • mysensors relay contest2017 switch light lighting • 27 Feb 2017, 18:03 • openhardware.io 12 Mar 2017, 15:54

💬 RFM69 - 8 relays board
OpenHardware.io • rfm69 relay • 24 Jan 2017, 13:33 • openhardware.io 24 Jan 2017, 13:33

0
Online

11.5k
Users

11.1k
Topics

112.8k
Posts

32 I2C Relay

Suggested Topics

Relay actuator sketch - auto off function Development • relay • 5 Dec 2014, 02:45 • niccodemi 11 Sept 2015, 15:27

RelayWithButtonActuator - another n00b question Troubleshooting • relay button actuator • 29 Jan 2015, 20:17 • gadu 1 Feb 2015, 19:04

Sensor reading incorrect data from the controller Bug Reports • relay openhab message.getbool getbool • 27 Feb 2016, 10:07 • Brian Fernando 27 Feb 2016, 10:07

Relay with ACS712 Hardware • relay nrf24l01+ • 27 Jan 2015, 15:36 • Dheeraj 30 Jun 2016, 21:18

💬 NModule OpenHardware.io • mysensors temperature relay humidity light pir nmodule door accelerometer touch milight • 23 May 2017, 14:38 • openhardware.io 10 May 2020, 05:43

💬 Homini AC Powered Relay (2) Module OpenHardware.io • mysensors relay contest2017 switch light lighting • 27 Feb 2017, 18:03 • openhardware.io 12 Mar 2017, 15:54

💬 RFM69 - 8 relays board OpenHardware.io • rfm69 relay • 24 Jan 2017, 13:33 • openhardware.io 24 Jan 2017, 13:33

0Online

11.5kUsers

11.1kTopics

112.8kPosts

Relay actuator sketch - auto off function
Development • relay • 5 Dec 2014, 02:45 • niccodemi 11 Sept 2015, 15:27

RelayWithButtonActuator - another n00b question
Troubleshooting • relay button actuator • 29 Jan 2015, 20:17 • gadu 1 Feb 2015, 19:04

Sensor reading incorrect data from the controller
Bug Reports • relay openhab message.getbool getbool • 27 Feb 2016, 10:07 • Brian Fernando 27 Feb 2016, 10:07

Relay with ACS712
Hardware • relay nrf24l01+ • 27 Jan 2015, 15:36 • Dheeraj 30 Jun 2016, 21:18

💬 NModule
OpenHardware.io • mysensors temperature relay humidity light pir nmodule door accelerometer touch milight • 23 May 2017, 14:38 • openhardware.io 10 May 2020, 05:43

💬 Homini AC Powered Relay (2) Module
OpenHardware.io • mysensors relay contest2017 switch light lighting • 27 Feb 2017, 18:03 • openhardware.io 12 Mar 2017, 15:54

💬 RFM69 - 8 relays board
OpenHardware.io • rfm69 relay • 24 Jan 2017, 13:33 • openhardware.io 24 Jan 2017, 13:33

0
Online

11.5k
Users

11.1k
Topics

112.8k
Posts