I see a lot of "!TSF" and "NACK" which seems to be radio communication problems.
That's MySensors related and can be related to many things, from soldering problem to power / capacitor issues.
In MY_DEBUG mode you should see your temp/hum printed on serial every ~15s so there is something wrong there, either wiring or a code issue.
Ty with the example included with the library "i2c_SI7021.h", without any MySensors related stuff, to see if your sensor is detected. You should see temp/hum on the serial.
@Samuel235 said in Homini AC Powered Relay (2) Module:
OMRON G3MB-202P
Okay I'm trying to help you with the fuse component.
I found a datasheet for the OMRON G3MB-202P. And there are enoght information to be known for fuse selection.
I try to calculate it here (and i will try it with my bad English ).
The most important information is the melting integral.
The Melting integral has A²s as unit. So this means the maximum current for a time can exists without damaging the device. For further information look at wikipedia.
So we need any further information about:
the protection which is present before (the typical circuit protection in private houses)
the melting integral from the device which we want to protect
the maximum voltage
the maximum switching current
the breaking capacity
Inrush current for the switched devices (we can't know)
Typical values for an automatic circuit breaker in private houses are:
from 25 to 100 A²s
230 V AC
16 A
So this protection isn't good enough for our relay. The relay have these values:
230 V AC
2 A maximum switching current
I²t value (melting integral): 4 A²s
the allowed inrush current over a small time is higher than the melting integral. It is a bit confusing i think, but if we calculate the protection for the given melting integral and it's fine. So we can define the parameters for the client (switching site of this application here)
The fuse have to be:
I²s value higher or equal than the I²s value from the existing protection
rating voltage over 230 V AC
rating current 2 A or lower (because 2 A is the maximum at 25 °C, for 40 °C it is about 1.6 A)
a maximum switching time of 1 second at 2 A or lower time with higher current but below 4A²s! To calculate use the switching time from the fuse datasheet an multiply it two times with the given current for this switching time.
And i think a fast blow fuse would be the best. There are SMD fuses with 10.1 x 3 mm and 250 V AC available.
If there is no fuse available with the values above, we could combine multiple fuses. A possible solution could be one bigger fuse for both relays and the ac/dc component. And a smaller fuse for the switching site of the relay and the HLK-PM01. But for this it is important that the circuit have only one input for the hot one (L) of 230 V and one output for each relay. In this case we could reduce the big connectors from 6 to 4. Like (L, N, Relay1, Relay2).
And the temperature fuse can work for all components too
So the protection for the primary site of the HLK-PM01 is a problem i think. Because the are no information available about the I²s value from HLK-PM01.
I hope you can understand my English and could follow my explanation?
This should work with Domoticz, it's what I intend to use with it. I've received the boards from China and I'm currently working on a version 2 of this board. There are some errors in the design of version 1 that I need to get out. New version will be up shortly.
When you read the data sheet correctly you can see, that the distance between the pins is different for a AA and AAA battery holder. That`s why I was asking if somebody can recommend a holder that fits.
@toyman said in NModule DC Fan / PWM shield:
Can the FET withstand continious 2A load? I have one meter long 5050 strip
FDD8447L is rated for 15A continuous load. You don't want to try that because it's possible only with a big pad and 2oz copper PCB, but 2A will not be a problem on this board, there's plenty of margin
https://isojed.nl/blog/wp-content/uploads/2013/06/FDD8447L.pdf
Oh, I never even thought of that as a possibility.
I really like KiCad, and it's my preference. For a while I had Eagle for work, but even then I still preferred KiCad whenever I was given a choice.
