Mysensors Gateway on OrangePi (Zero) (opi)
-
-
@Tag Does the TMRh20 works in the way your radio is currently connected?
-
@marceloaqno
The library compiled, but unfortunately i cannot get the examples for linux working.
need to edit i.e. gettingstarted.cpp with the correct pin setting, have tried a lot, but either it says that the radio is not connected, and if used with incorrect settings it will not compile at all....Maybe someone following this thread who has experince with this lib?
if there is any progress from my side will keep you posted...
-
If you used this wiring scheme:
nRF24L01 | Orange Pi _________|________________ VCC | VCC3V3-EXT GND | GND CSN | SPI0_CS0 (SPI-CE0) CE | PA7 (IO-7) MOSI | SPI0_MOSI (SPI-MOSI) SCK | SPI0_CLK (SPI-CLK) MISO | SPI0_MISO (SPI-MISO)
Then you should initialize the radio with:
RF24 radio(7,0);
Worked for me:
root@opi-pc-1:~/RF24-master/examples_linux# ./gettingstarted RF24/examples/GettingStarted/ STATUS = 0x0e RX_DR=0 TX_DS=0 MAX_RT=0 RX_P_NO=7 TX_FULL=0 RX_ADDR_P0-1 = 0x65646f4e32 0x65646f4e31 RX_ADDR_P2-5 = 0xc3 0xc4 0xc5 0xc6 TX_ADDR = 0x65646f4e32 RX_PW_P0-6 = 0x20 0x20 0x00 0x00 0x00 0x00 EN_AA = 0x3f EN_RXADDR = 0x02 RF_CH = 0x4c RF_SETUP = 0x07 CONFIG = 0x0e DYNPD/FEATURE = 0x00 0x00 Data Rate = 1MBPS Model = nRF24L01+ CRC Length = 16 bits PA Power = PA_MAX ************ Role Setup *********** Choose a role: Enter 0 for pong_back, 1 for ping_out (CTRL+C to exit)
-
@mihai.aldea Could you try the repo I'm working on (https://github.com/marceloaqno/MySensors/tree/spidev marceloaqno-spidev) adding your settings to the examples_linux/mysgw.cpp?
#define MY_RF24_CE_PIN 7 #define MY_RF24_CS_PIN 0
-
Hmmm.... checked the docs again and guess what. the 26 pin header on the OPI Zero has SPI1.... instead of SPI0
Expansion Port
The Orange Pi Zero has a 26-pin, 0.1" unpopulated connector with several low-speed interfaces. 2x13 Header 1 3.3V 2 5V 3 TWI0_SDA / PA12 4 5V 5 TWI0_SCK / PA11 6 GND 7 PWM1 / PA06 8 UART1_TX / PG06 9 GND 10 UART1_RX / PG07 11 UART2_RX / PA01 12 SIM_CLK/PA_EINT7 / PA07 13 UART2_TX / PA00 14 GND 15 UART2_CTS / PA03 16 TWI1-SDA / PA19 17 3.3V 18 TWI1-SCK / PA18 19 SPI1_MOSI / PA15 20 GND 21 SPI1_MISO / PA16 22 UART2_RTS / PA02 23 SPI1_CLK / PA14 24 SPI1_CS / PA13 25 GND 26 SIM_DET/PA_EINT10 / PA10
From http://linux-sunxi.org/Xunlong_Orange_Pi_Zero
If i look at /dev I only see spi0, which is most probably used for the onboard flash...root@orangepizero:/# ll /dev | grep -i spi crw------- 1 root root 153, 0 Jan 8 11:12 spidev0.0
So now i need to figure out a way to get SPI1 up and running
-
@marceloaqno Here's the output:
./MySensors.h:258:2: error: #error No support for nRF24 radio on this platform #error No support for nRF24 radio on this platform ^ In file included from ./drivers/RF24/RF24.cpp:23:0, from ./MySensors.h:294, from examples_linux/mysgw.cpp:77: ./drivers/RF24/RF24.h:52:17: fatal error: SPI.h: No such file or directory #include <SPI.h> ^ compilation terminated. Makefile:98: recipe for target 'build/examples_linux/mysgw.o' failed make: *** [build/examples_linux/mysgw.o] Error 1
-
@Tag Use this info:
http://linux-sunxi.org/Sunxi-tools
To export /boot/script.bin, edit the output file and enable SPI1, then compile it back and reboot your OPi with the SPI1 active.If you haven't done this before, it's quite simple.
apt-get install sunxi-tools cd ~ bin2fex /boot/script.bin > script.fex
Edit the script.fex file, find the [spi1] section and change spi_used = 0 to spi_used = 1. Save the file and exit.
Thenfex2bin script.fex > /boot/script.bin
Reboot, then you should have the SPI1 active.
-
@marceloaqno
i have error yet
orangepi is a good board. please work at this board and run mysensors gateway on this, i follow this topic when you can fix this on orange pi . thank you
-
Yep already found it problem was the old version of the tools, it was not able to decompile the script.bin file...
[update]
- modified the script file,
- changed spi_used = 1
- compiled back and rebooted
just 1 device file in called spidev0.0 no new device files are created.....
dmesg output:
[ 0.814287] sunxi_spi_chan_cfg()1376 - [spi-0] has no spi_regulator. [ 0.814316] sunxi_spi_chan_cfg()1376 - [spi-1] has no spi_regulator. [ 0.815569] spi spi0: master is unqueued, this is deprecated [ 0.816776] spi spi1: master is unqueued, this is deprecated
Thx, will keep you posted!
-
@Reza Was /sys/class/gpio/export created after modprobe gpio-sunxi?
@mihai-aldea Could you send the complete make and configure output so I can check if your system is correctly detected?
-
@marceloaqno said:
@mihai-aldea Could you send the complete make and configure output so I can check if your system is correctly detected?
Here it is
root@opi-pc-1:~/rf24opi/MySensors# ./configure --soc=H3 [OK] init system detected: systemd [SECTION] Saving configuration. [SECTION] Cleaning previous builds. [OK] Finished. root@opi-pc-1:~/rf24opi/MySensors# make gcc -MT build/drivers/Linux/log.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -c drivers/Linux/log.c -o build/drivers/Linux/log.o g++ -MT build/drivers/Linux/IPAddress.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -c drivers/Linux/IPAddress.cpp -o build/drivers/Linux/IPAddress.o g++ -MT build/drivers/Linux/noniso.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -c drivers/Linux/noniso.cpp -o build/drivers/Linux/noniso.o g++ -MT build/drivers/Linux/Print.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -c drivers/Linux/Print.cpp -o build/drivers/Linux/Print.o g++ -MT build/drivers/Linux/EthernetClient.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -c drivers/Linux/EthernetClient.cpp -o build/drivers/Linux/EthernetClient.o g++ -MT build/drivers/Linux/compatibility.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -c drivers/Linux/compatibility.cpp -o build/drivers/Linux/compatibility.o g++ -MT build/drivers/Linux/SerialPort.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -c drivers/Linux/SerialPort.cpp -o build/drivers/Linux/SerialPort.o g++ -MT build/drivers/Linux/Stream.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -c drivers/Linux/Stream.cpp -o build/drivers/Linux/Stream.o g++ -MT build/drivers/Linux/SoftEeprom.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -c drivers/Linux/SoftEeprom.cpp -o build/drivers/Linux/SoftEeprom.o g++ -MT build/drivers/Linux/EthernetServer.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -c drivers/Linux/EthernetServer.cpp -o build/drivers/Linux/EthernetServer.o g++ -MT build/examples_linux/mysgw.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -c examples_linux/mysgw.cpp -o build/examples_linux/mysgw.o In file included from examples_linux/mysgw.cpp:77:0: ./MySensors.h:258:2: error: #error No support for nRF24 radio on this platform #error No support for nRF24 radio on this platform ^ In file included from ./drivers/RF24/RF24.cpp:23:0, from ./MySensors.h:294, from examples_linux/mysgw.cpp:77: ./drivers/RF24/RF24.h:52:17: fatal error: SPI.h: No such file or directory #include <SPI.h> ^ compilation terminated. Makefile:98: recipe for target 'build/examples_linux/mysgw.o' failed make: *** [build/examples_linux/mysgw.o] Error 1
-
@mihai.aldea I think you're not in the right branch, could you start from scratch like this:
rm -rf marceloaqno-spidev git clone https://github.com/marceloaqno/MySensors marceloaqno-spidev cd marceloaqno-spidev git checkout spidev ./configure make
-
@marceloaqno
i have not any folder "gpio" in class folder .
what am i do ?
can you create a new topic with all steps after full fix on orange pi ?
thank you. i follow this topic
-
@marceloaqno You were right, I wasn't using the correct branch. Your instructions though did not work for me
root@opi-pc-1:~# git clone https://github.com/marceloaqno/MySensors/tree/spidev marceloaqno-spidev Cloning into 'marceloaqno-spidev'... fatal: repository 'https://github.com/marceloaqno/MySensors/tree/spidev/' not found
Anyway, I found another way:
git clone https://github.com/marceloaqno/MySensors.git marceloaqno-spidev cd marceloaqno-spidev/ git pull origin spidev ./configure make
This time it compiled successfuly, but when I fired up mysgw all I got was:
mysgw: Starting gateway... mysgw: Protocol version - 2.2.0-beta
with no other output.
Just to be sure we're on the same note, what is the wiring schematic I should use? When I first started to tinker with RF24 on OPi I found at least two wiring schematics.
For reference here's the gpio readall on my OPi PC:+-----+-----+----------+------+---+-Orange Pi+---+---+------+---------+-----+--+ | BCM | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | BCM | +-----+-----+----------+------+---+----++----+---+------+----------+-----+-----+ | | | 3.3v | | | 1 || 2 | | | 5v | | | | 12 | 8 | SDA.0 | ALT5 | 0 | 3 || 4 | | | 5V | | | | 11 | 9 | SCL.0 | ALT5 | 0 | 5 || 6 | | | 0v | | | | 6 | 7 | GPIO.7 | ALT3 | 0 | 7 || 8 | 0 | ALT4 | TxD3 | 15 | 13 | | | | 0v | | | 9 || 10 | 0 | ALT4 | RxD3 | 16 | 14 | | 1 | 0 | RxD2 | ALT5 | 0 | 11 || 12 | 0 | ALT3 | GPIO.1 | 1 | 110 | | 0 | 2 | TxD2 | ALT5 | 1 | 13 || 14 | | | 0v | | | | 3 | 3 | CTS2 | ALT5 | 0 | 15 || 16 | 0 | ALT3 | GPIO.4 | 4 | 68 | | | | 3.3v | | | 17 || 18 | 0 | ALT3 | GPIO.5 | 5 | 71 | | 64 | 12 | MOSI | ALT4 | 0 | 19 || 20 | | | 0v | | | | 65 | 13 | MISO | ALT4 | 0 | 21 || 22 | 0 | ALT5 | RTS2 | 6 | 2 | | 66 | 14 | SCLK | ALT4 | 0 | 23 || 24 | 0 | ALT4 | CE0 | 10 | 67 | | | | 0v | | | 25 || 26 | 0 | ALT3 | GPIO.11 | 11 | 21 | | 19 | 30 | SDA.1 | ALT4 | 0 | 27 || 28 | 0 | ALT4 | SCL.1 | 31 | 18 | | 7 | 21 | GPIO.21 | ALT3 | 0 | 29 || 30 | | | 0v | | | | 8 | 22 | GPIO.22 | ALT3 | 0 | 31 || 32 | 0 | ALT5 | RTS1 | 26 | 200 | | 9 | 23 | GPIO.23 | OUT | 0 | 33 || 34 | | | 0v | | | | 10 | 24 | GPIO.24 | OUT | 1 | 35 || 36 | 0 | ALT5 | CTS1 | 27 | 201 | | 20 | 25 | GPIO.25 | ALT3 | 0 | 37 || 38 | 0 | ALT5 | TxD1 | 28 | 198 | | | | 0v | | | 39 || 40 | 0 | ALT5 | RxD1 | 29 | 199 | +-----+-----+----------+------+---+----++----+---+------+----------+-----+-----+ | BCM | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | BCM | +-----+-----+----------+------+---+-Orange Pi+---+------+----------+-----+-----+
-
Just a question the command "gpio readall" does that does show the actual status of the system, or is it just a fixed table that is printed on screen....
Look at mine:
root@orangepizero:~# gpio readall +-----+-----+----------+------+---+-Orange Pi+---+---+------+---------+-----+--+ | BCM | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | BCM | +-----+-----+----------+------+---+----++----+---+------+----------+-----+-----+ | | | 3.3v | | | 1 || 2 | | | 5v | | | | 12 | 8 | SDA.0 | ALT5 | 0 | 3 || 4 | | | 5V | | | | 11 | 9 | SCL.0 | ALT5 | 0 | 5 || 6 | | | 0v | | | | 6 | 7 | GPIO.7 | ALT3 | 0 | 7 || 8 | 1 | OUT | TxD3 | 15 | 13 | | | | 0v | | | 9 || 10 | 0 | ALT5 | RxD3 | 16 | 14 | | 1 | 0 | RxD2 | ALT5 | 0 | 11 || 12 | 0 | ALT3 | GPIO.1 | 1 | 110 | | 0 | 2 | TxD2 | ALT5 | 0 | 13 || 14 | | | 0v | | | | 3 | 3 | CTS2 | ALT3 | 0 | 15 || 16 | 0 | ALT3 | GPIO.4 | 4 | 68 | | | | 3.3v | | | 17 || 18 | 0 | ALT3 | GPIO.5 | 5 | 71 | | 64 | 12 | MOSI | ALT4 | 0 | 19 || 20 | | | 0v | | | | 65 | 13 | MISO | ALT4 | 0 | 21 || 22 | 0 | OUT | RTS2 | 6 | 2 | | 66 | 14 | SCLK | ALT4 | 0 | 23 || 24 | 0 | ALT4 | CE0 | 10 | 67 | | | | 0v | | | 25 || 26 | 0 | ALT3 | GPIO.11 | 11 | 21 | | 19 | 30 | SDA.1 | ALT4 | 0 | 27 || 28 | 0 | ALT4 | SCL.1 | 31 | 18 | | 7 | 21 | GPIO.21 | ALT3 | 0 | 29 || 30 | | | 0v | | | | 8 | 22 | GPIO.22 | ALT3 | 0 | 31 || 32 | 0 | ALT3 | RTS1 | 26 | 200 | | 9 | 23 | GPIO.23 | OUT | 0 | 33 || 34 | | | 0v | | | | 10 | 24 | GPIO.24 | OUT | 1 | 35 || 36 | 0 | ALT3 | CTS1 | 27 | 201 | | 20 | 25 | GPIO.25 | OUT | 1 | 37 || 38 | 0 | ALT5 | TxD1 | 28 | 198 | | | | 0v | | | 39 || 40 | 0 | ALT5 | RxD1 | 29 | 199 | +-----+-----+----------+------+---+----++----+---+------+----------+-----+-----+ | BCM | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | BCM | +-----+-----+----------+------+---+-Orange Pi+---+------+----------+-----+-----+
It is the same... and shows 40 pins while the OPI Zero only has 26.......
There are some small differences between our tables in the naming column... so i guess it really reads the status / names of the pins.. Anyhow still strange that 40 pins are shown instead of 26 for the zero..
-
@marceloaqno: are you planning to create a pull request? also, like @Reza suggested i think it would be smart to gather all information somehwhere, unfortunately mysensors does not seem to have a wiki. can we write an article somehow? i could take care of that.
-
@mihai.aldea sorry about the github link mistake.
@pansen Yes, I will.
Is the orientation of the pins correct in the image?
-
Nope pinout is reversed!,
The link below shows the correct one!
https://oshlab.com/orange-pi-zero-pinout/
-
@Tag Oops, did I get it right this time (I reuploaded the image)?
-
Build the RF24 lib, without erros on the OPI Zero. and am now able to start the tools and radio seems to be recognised!. (was a faulty breadboard wire.... )
Used the follwing to for the radio:
RF24 radio(2,0);
Output from gettingstarted:
root@orangepizero:~/rf24libs/RF24/examples_linux# ./gettingstarted RF24/examples/GettingStarted/ STATUS = 0x00 RX_DR=0 TX_DS=0 MAX_RT=0 RX_P_NO=0 TX_FULL=0 RX_ADDR_P0-1 = 0x0000000000 0xff00000000 RX_ADDR_P2-5 = 0xff 0xff 0xff 0xff TX_ADDR = 0xffffffffff RX_PW_P0-6 = 0xff 0xff 0xff 0xff 0xff 0xff EN_AA = 0xff EN_RXADDR = 0xff RF_CH = 0xbc RF_SETUP = 0xff CONFIG = 0xff DYNPD/FEATURE = 0xff 0xff Data Rate = 1MBPS Model = nRF24L01 CRC Length = 16 bits PA Power = PA_MAX ************ Role Setup *********** Choose a role: Enter 0 for pong_back, 1 for ping_out (CTRL+C to exit) >
-
@Tag Could you fill this table with your current setup?
nRF24L01 | OrangePi | OrangePi | phyPin | GPIO _________|_______________________ VCC | 3V3-PWR | 3V3-PWR GND | GND | GND CSN | | CE | | MOSI | 19 | 15 SCK | 23 | 14 MISO | 21 | 16
-
Sure here it is,
nRF24L01 | OrangePi | OrangePi | phyPin | GPIO _________|_______________________ VCC | 3V3-PWR | 3V3-PWR GND | GND | GND CSN | 24 | 13 CE | 22 | 2 MOSI | 19 | 15 SCK | 23 | 14 MISO | 21 | 16
Radio seems to be recognised, still need to test data transfer...
-
I created the draft for the official article: https://www.mysensors.org/build/orange
-
@marceloaqno and everyone else involved in this effort: great work! I love when people come together to solve a problem.
-
@marceloaqno
@mfalkvidd @Tag @pansen @Reza @mihai.aldea @hausingerWooow woow woow !!!
Only few days "off" and the problem to make work Mysensors on OPI are solved.
So many many thanks to all people here that have been involved to make that OPI good little boards can work with Mysensors.
This is the proof that when good people join can reach the most difficult achievements and all humanity can benefit.
Awesome work !
Regards
-
Great work!!! the GPIO part most probably needs some additions for OPI zero on the topic of the spidev1.0 driver and the GPIO pins, send it to you once i got everything documented.
Really many thanks for your hard work here!!
-
This post is deleted!
-
@marceloaqno
thank you. but i have error:root@OrangePI:~# ls /sys/class/gpio/export ls: cannot access /sys/class/gpio/export: No such file or directory root@OrangePI:~# modprobe gpio-sunxi root@OrangePI:~# ls /sys/class/gpio/export ls: cannot access /sys/class/gpio/export: No such file or directory
in class folder i dont have gpio folder (i use a orangepi one with ubuntu os )
i
-
You need to create the files after each boot.
After the modprobe, Issue this command:
sudo for A in 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16; do echo "$A" > /sys/class/gpio/export ; done
This will get you the files.
-
root@OrangePI:~# git clone https://github.com/marceloaqno/MySensors.git orangepi Cloning into 'orangepi'... remote: Counting objects: 13858, done. remote: Compressing objects: 100% (50/50), done. remote: Total 13858 (delta 17), reused 0 (delta 0), pack-reused 13808 Receiving objects: 100% (13858/13858), 9.68 MiB | 79.00 KiB/s, done. Resolving deltas: 100% (8304/8304), done. Checking connectivity... done. root@OrangePI:~# cd orangepi/ root@OrangePI:~/orangepi# git pull origin spidev From https://github.com/marceloaqno/MySensors * branch spidev -> FETCH_HEAD Updating 570b607..63e1a81 Fast-forward Makefile | 16 +++ MyConfig.h | 4 + MySensors.h | 2 +- configure | 79 ++++++++++--- core/MyHwLinuxGeneric.cpp | 17 +++ core/MyHwLinuxGeneric.h | 12 +- core/MyHwRPi.cpp | 1 + core/MyHwRPi.h | 28 ----- core/MyMainLinux.cpp | 30 ++--- drivers/{RPi => BCM}/SPI.cpp | 10 +- drivers/{RPi => BCM}/SPI.h | 116 ++++++++++++------- drivers/{RPi => BCM}/Wire.cpp | 0 drivers/{RPi => BCM}/Wire.h | 1 + drivers/Linux/Arduino.h | 22 +++- drivers/Linux/GPIO.cpp | 119 ++++++++++++++++++++ drivers/Linux/GPIO.h | 47 ++++++++ drivers/Linux/Stream.h | 1 + drivers/Linux/compatibility.cpp | 11 +- drivers/{RPi/rpi_util.cpp => Linux/interrupt.cpp} | 144 +++++------------------- drivers/Linux/interrupt.h | 45 ++++++++ drivers/RF24/RF24.cpp | 4 +- drivers/RF24/RF24.h | 2 +- drivers/RPi/RPi.cpp | 59 ++++++++++ drivers/RPi/RPi.h | 22 ++++ drivers/RPi/piHiPri.c | 49 -------- drivers/RPi/rpi_util.h | 76 ------------- drivers/RPi/wiring.cpp | 72 ++++++++++++ drivers/RPi/wiring.h | 24 ++++ drivers/SPIDEV/SPI.cpp | 223 +++++++++++++++++++++++++++++++++++++ drivers/SPIDEV/SPI.h | 178 +++++++++++++++++++++++++++++ 30 files changed, 1054 insertions(+), 360 deletions(-) rename drivers/{RPi => BCM}/SPI.cpp (100%) rename drivers/{RPi => BCM}/SPI.h (62%) rename drivers/{RPi => BCM}/Wire.cpp (100%) rename drivers/{RPi => BCM}/Wire.h (99%) create mode 100644 drivers/Linux/GPIO.cpp create mode 100644 drivers/Linux/GPIO.h rename drivers/{RPi/rpi_util.cpp => Linux/interrupt.cpp} (63%) create mode 100644 drivers/Linux/interrupt.h create mode 100644 drivers/RPi/RPi.cpp create mode 100644 drivers/RPi/RPi.h delete mode 100644 drivers/RPi/piHiPri.c delete mode 100644 drivers/RPi/rpi_util.h create mode 100644 drivers/RPi/wiring.cpp create mode 100644 drivers/RPi/wiring.h create mode 100644 drivers/SPIDEV/SPI.cpp create mode 100644 drivers/SPIDEV/SPI.h root@OrangePI:~/orangepi# ./configure [SECTION] Detecting target machine. [OK] machine detected: SoC=H3, Type=unknown, CPU=armv7l. [SECTION] Detecting SPI driver. [OK] SPI driver detected:SPIDEV. [SECTION] Detecting init system. [OK] init system detected: systemd. [SECTION] Saving configuration. [SECTION] Cleaning previous builds. [OK] Finished. root@OrangePI:~/orangepi# make gcc -MT build/drivers/Linux/log.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DLINUX_ARCH_ORANGEPI -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/log.c -o build/drivers/Linux/log.o g++ -MT build/drivers/Linux/IPAddress.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DLINUX_ARCH_ORANGEPI -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/IPAddress.cpp -o build/drivers/Linux/IPAddress.o g++ -MT build/drivers/Linux/noniso.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DLINUX_ARCH_ORANGEPI -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/noniso.cpp -o build/drivers/Linux/noniso.o g++ -MT build/drivers/Linux/GPIO.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DLINUX_ARCH_ORANGEPI -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/GPIO.cpp -o build/drivers/Linux/GPIO.o g++ -MT build/drivers/Linux/Print.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DLINUX_ARCH_ORANGEPI -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/Print.cpp -o build/drivers/Linux/Print.o g++ -MT build/drivers/Linux/EthernetClient.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DLINUX_ARCH_ORANGEPI -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/EthernetClient.cpp -o build/drivers/Linux/EthernetClient.o g++ -MT build/drivers/Linux/SerialPort.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DLINUX_ARCH_ORANGEPI -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/SerialPort.cpp -o build/drivers/Linux/SerialPort.o g++ -MT build/drivers/Linux/Stream.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DLINUX_ARCH_ORANGEPI -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/Stream.cpp -o build/drivers/Linux/Stream.o g++ -MT build/drivers/Linux/compatibility.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DLINUX_ARCH_ORANGEPI -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/compatibility.cpp -o build/drivers/Linux/compatibility.o g++ -MT build/drivers/Linux/interrupt.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DLINUX_ARCH_ORANGEPI -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/interrupt.cpp -o build/drivers/Linux/interrupt.o drivers/Linux/interrupt.cpp: In function ‘void* interruptHandler(void*)’: drivers/Linux/interrupt.cpp:107:26: warning: ignoring return value of ‘ssize_t read(int, void*, size_t)’, declared with attribute warn_unused_result [-Wunused-result] (void)read (fd, &c, 1) ; ^ g++ -MT build/drivers/Linux/SoftEeprom.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DLINUX_ARCH_ORANGEPI -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/SoftEeprom.cpp -o build/drivers/Linux/SoftEeprom.o g++ -MT build/drivers/Linux/EthernetServer.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DLINUX_ARCH_ORANGEPI -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/EthernetServer.cpp -o build/drivers/Linux/EthernetServer.o g++ -MT build/examples_linux/mysgw.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DLINUX_ARCH_ORANGEPI -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c examples_linux/mysgw.cpp -o build/examples_linux/mysgw.o In file included from ./MySensors.h:294:0, from examples_linux/mysgw.cpp:74: ./drivers/RF24/RF24.cpp:39:11: error: Not supported on this platform. hwDigitalWrite(MY_RF24_CS_PIN, level); ^ ./drivers/RF24/RF24.cpp:44:11: error: Not supported on this platform. hwDigitalWrite(MY_RF24_CE_PIN, level); ^ ./drivers/RF24/RF24.cpp:388:11: error: Not supported on this platform. hwPinMode(MY_RF24_CE_PIN,OUTPUT); ^ ./drivers/RF24/RF24.cpp:389:11: error: Not supported on this platform. hwPinMode(MY_RF24_CS_PIN,OUTPUT); ^ ./drivers/RF24/RF24.cpp:37:32: warning: unused parameter ‘level’ [-Wunused-parameter] LOCAL void RF24_csn(const bool level) ^ ./drivers/RF24/RF24.cpp:42:31: warning: unused parameter ‘level’ [-Wunused-parameter] LOCAL void RF24_ce(const bool level) ^ ./drivers/RF24/RF24.cpp: In function ‘uint8_t RF24_spiMultiByteTransfer(uint8_t, uint8_t*, uint8_t, bool)’: ./drivers/RF24/RF24.cpp:56:11: error: ‘LOW’ was not declared in this scope RF24_csn(LOW); ^ ./drivers/RF24/RF24.cpp:99:11: error: ‘HIGH’ was not declared in this scope RF24_csn(HIGH); ^ ./drivers/RF24/RF24.cpp: In function ‘void RF24_startListening()’: ./drivers/RF24/RF24.cpp:235:10: error: ‘HIGH’ was not declared in this scope RF24_ce(HIGH); ^ ./drivers/RF24/RF24.cpp: In function ‘void RF24_stopListening()’: ./drivers/RF24/RF24.cpp:241:10: error: ‘LOW’ was not declared in this scope RF24_ce(LOW); ^ ./drivers/RF24/RF24.cpp: In function ‘void RF24_powerDown()’: ./drivers/RF24/RF24.cpp:251:10: error: ‘LOW’ was not declared in this scope RF24_ce(LOW); ^ ./drivers/RF24/RF24.cpp: In function ‘bool RF24_sendMessage(uint8_t, const void*, uint8_t)’: ./drivers/RF24/RF24.cpp:269:10: error: ‘HIGH’ was not declared in this scope RF24_ce(HIGH); ^ ./drivers/RF24/RF24.cpp:276:10: error: ‘LOW’ was not declared in this scope RF24_ce(LOW); ^ ./drivers/RF24/RF24.cpp: In function ‘bool RF24_initialize()’: ./drivers/RF24/RF24.cpp:395:10: error: ‘LOW’ was not declared in this scope RF24_ce(LOW); ^ ./drivers/RF24/RF24.cpp:396:11: error: ‘HIGH’ was not declared in this scope RF24_csn(HIGH); ^ Makefile:114: recipe for target 'build/examples_linux/mysgw.o' failed make: *** [build/examples_linux/mysgw.o] Error 1 root@OrangePI:~/orangepi#```
-
root@OrangePI:~/orangepi# sudo for A in 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16; do echo "$A" > /sys/class/gpio/export ; done -bash: syntax error near unexpected token `do' root@OrangePI:~/orangepi# ```
-
@Tag said:
sudo for A in 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16; do echo "$A" > /sys/class/gpio/export ; done
orangepi one have 40 pins
-
@Reza Is there /sys/class/gpio/export file on your OPi?
-
@marceloaqno
no i have not folder "gpio" in my orangepi
-
@marceloaqno It still doesn't work on my OPi Zero
root@opi-zero-1:~/orangepi# bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.2.0-beta
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:PDT
mysgw: Received SIGINTI do have the /sys/class/gpio/export and I ran for A in 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16; do echo "$A" > /sys/class/gpio/export ; done
For the record, here's my OS:
BOARD=orangepizero BOARD_NAME="Orange Pi Zero" VERSION=5.24 LINUXFAMILY=sun8i BRANCH=default ARCH=arm PRETTY_NAME="Debian GNU/Linux 8 (jessie)" NAME="Debian GNU/Linux" VERSION_ID="8" VERSION="8 (jessie)" ID=debian HOME_URL="http://www.debian.org/" SUPPORT_URL="http://www.debian.org/support" BUG_REPORT_URL="https://bugs.debian.org/"
-
@mihai.aldea The gateway does the exporting when needed, you don't need to run:
for A in 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16; do echo "$A" > /sys/class/gpio/export ; doneCould you send the output of this command?
ls -lah /dev/spidev*
-
Still issues here:
root@orangepizero:~/orangepi/bin# ll /dev/spi* crw------- 1 root root 153, 0 Jan 9 22:51 /dev/spidev0.0 crw------- 1 root root 153, 1 Jan 9 22:51 /dev/spidev1.0
Then:
./configure --spi-spidev-device=/dev/spidev1.0
added to examples_linux/mysgw.cpp
#define MY_RF24_CE_PIN 2 #define MY_RF24_CS_PIN 13
end enabled radio debugging:
output:
root@orangepizero:~/orangepi/bin# ./mysgw -d mysgw: Starting gateway... mysgw: Protocol version - 2.2.0-beta mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.2.0-beta mysgw: TSM:INIT mysgw: TSF:WUR:MS=0 mysgw: RF24:write register, reg=0, value=14 mysgw: RF24:write register, reg=3, value=3 mysgw: RF24:write register, reg=4, value=95 mysgw: RF24:write register, reg=5, value=76 mysgw: RF24:write register, reg=6, value=39 mysgw: RF24:write register, reg=16, value=115 mysgw: RF24:write register, reg=29, value=6 mysgw: RF24:read register, reg=6, value=39 mysgw: RF24:read register, reg=5, value=76 mysgw: RF24:write register, reg=2, value=2 mysgw: RF24:write register, reg=1, value=0 mysgw: RF24:write register, reg=28, value=3 mysgw: RF24:flushRX mysgw: RF24:flushTX mysgw: RF24:write register, reg=7, value=112 mysgw: TSM:INIT:TSP OK mysgw: TSM:INIT:GW MODE mysgw: RF24:write register, reg=2, value=3 mysgw: RF24:write register, reg=1, value=1 mysgw: RF24:STRT LIS mysgw: RF24:write register, reg=0, value=15 mysgw: RF24:write register, reg=10, value=0 mysgw: TSM:READY:ID=0,PAR=0,DIS=0 mysgw: MCO:REG:NOT NEEDED mysgw: RF24:read register, reg=23, value=17 Illegal instruction root@orangepizero:~/orangepi/bin#
Almost there?
-
@marceloaqno
in "orangepi one"(ubuntu os) there is not gpio folder in sys/class. but i think after run "modprobe gpio-sunxi" built a folder that name is "gpio_sw" and in this folder there are this files: normal_led,pa3,pa6,pa8 and 9,10,13,14,15,21 ,...
-
@Reza Is it too complicated to switch to Debian?
-
@mihai.aldea said:
Is it too complicated to switch to Debian?
you told me i change my os ? to armbian ?
-
@Reza
More info on armbian.comI use the debian jessie, works like a charm!
-
@Reza I wouldn't even dream of not using Armbian on OrangePi and NanoPi. Compared to Raspbian it's years ahead in terms of optimization and tidyness. Armbian is the reason I'm avoiding RPi when possible. So go ahead and install a proper OS for your OPi. Not sure if Xenial or Debian, maybe we should wait for @marceloaqno to respond to my comment with the running OS.
-
@Tag
i worked with armbiam before. but my question is with armbian my problem is resolve ?
-
That I can not say.
-
-
I confirm it's not working on the OPi PC where TMRh20 works.
-
@marceloaqno said:
@Tag Oops, did I get it right this time (I reuploaded the image)?
Got it spot on!! looks great!
-
i have problem with compile source domoticz(i must use source domoticz for my changes) in armbian, so i have to use ubuntu.
@marceloaqno can you help me to run mysensors gateway in orangepi one (ubuntu os).thank you
-
Hi All,
I put together the steps to get MySensors running on the OrangePi Zero:
Take note of the SPI part, 1 typo and you will not see /dev/spidev1.0-
Download and Install the ARMbian(debian) OS image
https://www.armbian.com/orange-pi-zero/ -
Install sunxi-tools:
These tools are required to make changes in the boot area of the system
sudo apt-get update sudo apt-get install sunxi-tools
- How to add /dev/spidev1.0 (which is required since /dev/spidev0.0 is used for the onboard NAND flash)
cd /boot bin2fex /boot/script.bin /root/myscript.txt
Now edit /root/myscript.bin and add/change the following so it looks exactly like the part below:
[spi0] spi_used = 1 spi_cs_bitmap = 1 spi_mosi = port:PC00<3><default><default><default> spi_miso = port:PC01<3><default><default><default> spi_sclk = port:PC02<3><default><default><default> spi_cs0 = port:PC03<3><1><default><default> [spi1] spi_used = 1 spi_cs_bitmap = 1 spi_cs0 = port:PA13<2><1><default><default> spi_sclk = port:PA14<2><default><default><default> spi_mosi = port:PA15<2><default><default><default> spi_miso = port:PA16<2><default><default><default> [spi_devices] spi_dev_num = 2 [spi_board0] modalias = "spidev" max_speed_hz = 33000000 bus_num = 0 chip_select = 0 mode = 0 full_duplex = 1 manual_cs = 0 [spi_board1] modalias = "spidev" max_speed_hz = 33000000 bus_num = 1 chip_select = 0 mode = 0 full_duplex = 1 manual_cs = 0
- Then recompile the script file:
fex2bin /root/myscript.txt /boot/script.bin
Reboot the system
reboot
2 device files should exist now:
root@orangepizero:~# ls -l /dev/spi* crw------- 1 root root 153, 0 Jan 11 16:31 /dev/spidev0.0 crw------- 1 root root 153, 1 Jan 11 16:31 /dev/spidev1.0
Load the gpio module
modprobe gpio-sunxi
To load the module gpio-sunxi automagically load at boot time, add gpio-sunxi to /etc/modules
echo gpio-sunxi >> /etc/modules
- Now it is time to install the GW.
cd /root git clone https://github.com/marceloaqno/MySensors.git orangepi cd orangepi/ git pull origin spidev ./configure --spi-spidev-device=/dev/spidev1.0 make
Working like a charm!
If you tested "/bin/mysgw -d" and all works as expected, make the installation permanent:
make install
Additional
If you want to read data into a controller using a device file (i.e Mycontroller) use the build string below./configure --spi-spidev-device=/dev/spidev1.0 --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyMySensorsGateway
Hope this helps!! have fun!!
-
-
@Tag great! Thanks for the detailed explanation
I will add to the instructions page
-
out of curiousity: this all relates to 3.x kernel in armbian right? which has proprietary stuff in there?
i read somewhere that mainline 4.10 SPI is "work in progress"
-
@pansen
Yes correct, for OPI Zero only ARMbian 3.x is available as a download image.
I used the debian jessie one
-
Instructions page updated, let me know if there is any mistake.
-
looks great!! thx!!
-
Excellent work !!! It finally works, I believe the slight mistake was with the damn SPI device ID. Now that I've enabled /dev/spidev1.0 everything works perfect. Really nice job and awesome commitment to showing people that it's time for them to pull their heads out of their a.... and spend less for way more awesome boards because let's face it, RPi has the greatest community support but it's a nothing more than an expensive closed source crappy board.
-
@mihai.aldea
Great!!, found out the SPI0 is used for the NAND flash, once you add SPI1 to the script.bin, also the need board paragraph with bus 1 needs to be added otherwise it will not work.... anyway great you got mysensors up and running!!
About the RPI, i like both boards, and in my opinion the enormous success of the RPI is responsible, for the large collection of OPI boards that is available these days
-
There are few who know that lots of asian compaines were producing SBC's long before RPi ever existed. RPi has to take credit for the SBC boom, but the connaisseurs will always prefer a top notch SBC that costs less than half of an RPi and is piled with features. Take the OPi Zero for instance, it's way smaller than RPi 3, has half the RAM and doesn't have Bluetooth. But you can buy 4 OPi Zeros with the money you'd spend on an RPi 3.
Anyway it's an endless debate here, I'm just glad I could help a bit bringing this to life, even though you and @marceloaqno did the heavy lifting.
-
Thank you for the hard work guys, I have a fresh orange pi zero and I will install armbian and try this hack as soon as possible. Looks like a great way to have an ultra compact&cheap controller + gateway system !
-
Support for OrangePi is now part of the official MySensors development repository.
In the official version, it is necessary to define the CE and CS pins, as the default ones will not work. This will change in the future, but more work needs to be done to better detect the different types of Orange Pi and other H3 soc boards.
For now, if you have set your system in the same way as the wiring instructions, use:./configure --spi-spidev-device=/dev/spidev1.0 --my-transport=nrf24 --my-rf24-ce-pin=2 --my-rf24-cs-pin=13
-
Thank you for your hard work and continued support on this!!
-
@mihai.aldea
It's working on my OPi One with Armbian. MySensors and TMRh20 works!Only in ./MySensors: bin Only in ./MySensors: build diff -ruBdX ex ./_MySensors/drivers/RF24/RF24.cpp ./MySensors/drivers/RF24/RF24.cpp --- ./_MySensors/drivers/RF24/RF24.cpp<>2017-01-28 10:24:03.557215399 +0200 +++ ./MySensors/drivers/RF24/RF24.cpp<->2017-01-28 10:58:51.757543157 +0200 @@ -29,7 +29,7 @@ LOCAL RF24_receiveCallbackType RF24_receiveCallback = NULL; #endif . -#ifdef LINUX_SPI_BCM +#if defined (LINUX_SPI_BCM) || (LINUX_SPI_SPIDEV) uint8_t spi_rxbuff[32+1] ; //SPI receive buffer (payload max 32 bytes) uint8_t spi_txbuff[32+1] ; //SPI transmit buffer (payload max 32 bytes + 1 byte for the command) #endif @@ -56,7 +56,7 @@ <----->RF24_csn(LOW); <----->// timing <----->delayMicroseconds(10); -#ifdef LINUX_SPI_BCM +#if defined (LINUX_SPI_BCM) || (LINUX_SPI_SPIDEV) <----->uint8_t * prx = spi_rxbuff; <----->uint8_t * ptx = spi_txbuff; <----->uint8_t size = len + 1; // Add register value to transmit buffer diff -ruBdX ex ./_MySensors/Makefile.inc ./MySensors/Makefile.inc --- ./_MySensors/Makefile.inc<->2017-01-28 10:49:53.990638008 +0200 +++ ./MySensors/Makefile.inc<-->2017-01-28 11:12:57.601198157 +0200 @@ -1,5 +1,5 @@ SOC=H3 -CPPFLAGS=-march=armv7-a -mtune=cortex-a7 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV. +CPPFLAGS=-march=armv7-a -mtune=cortex-a7 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DLINUX_SPI_SPIDEV -DMY_RF24_CE_PIN=7 -DSPI_S LDFLAGS=-pthread. PREFIX=/usr/local CC=gcc
-
Hi all
I want to give feedback here.
Today i tried to build a orange pi gateway with a connected usb - rs485 converter on it. And what should I say - It worked without problems. Many thanks to you all
Great
-
Hi to all, I don't know if this is the right thread, but I'm trying to use an odroid c1 as a gateway. I'm posting here because I think you all could help me.
The original thread I have done is this one
https://forum.mysensors.org/topic/6083/odroid-c1-as-getaway
Feel free to go over there and give me advises.