@OliverDog You may have a look at https://github.com/sidoh/esp8266_milight_hub. It uses basically the same hardware as a normal MySensors Wifi-GW and is able to receive and send (most) of the MiLight-Codes. I'm using the MQTT interface offered by the hub not only to translate MiLight-V5-protocol type of remote codes not only to control V4-protocol type of rgbw bulbs (which seems to be close to your request), but also to set shutter levels or even control my mpd... Obviously, this nees some additional coding on controller side (FHEM in my case).

@activemind do you already have a BOM? and is there chance to help you out? I would be willing to assemble one or two of the boards :bowtie:

@Nca78 said in Particle Powered Air Quality Sensor Logging to Google Docs: @Sebex said in Particle Powered Air Quality Sensor Logging to Google Docs: Perhaps I don't necessarily need to use the same pins Both the sensors you quote are using I2C. So they both use the same 2 pins (SDA, SCL) to communicate. You can put many I2C sensors on those same pins, they each have an address to know which sensor is receiving/sending data to the master (here, your arduino). Look for a tutorial on I2C first. Thanks I get it now :smile:

Sorry for the huge kick.. But I seem to have the same ethernet gateway as TS. His his wire diagram valid?

@martinhjelmare As soon as i have the time (and clean up my code because it was a hack) i'll create a pull request. i've mine also at 0.02 and my (pi zero) CPU is now at around 8-10%.

@korttoma Hello Sir, many thanks for such an elegant piece of code for controlling multiple relays. I would greatly appreciate if you provide me some tips or updated code on using your code for a "Bi stable" Button setup, i.e. using conventional home switches (ON or OFF states) for controlling relays. Thanks T

It would be great to see some improvements added to MySensors lib. Like a good message Queue and stuff like that. Ways to get more state out of the lib so you can provide a bit more user feedback. Right now I have some of those in my own lib. When I have time I'll post some on this forum. So others might benefit. But I'm currently hooked up to modular synths. Learning a lot of analog technology. Which broadens my Arduino horizon.

@axillent thanks and what is the smd coil that you use?

Ok tested as show in previus post. And the same problem. Maybe a little better. But maybe no... On 2.2.0 is a very very better.

@LastSamurai, Very nice project you have here! Thank you for taking the time to post/share your work! At first I thought it might be exactly what I was looking for, but reading through everything now I am not so sure. I have been studying various ways (Wi-Fi, 433/315 Mhz RF, MySensors) to implement controlling RGB lights and I initially thought Wi-Fi (while readily available, easy, and cheap) might be too "slow" in response time, which got me thinking to use MySensors (with NRF24) instead, which led me to this thread (among others). Something concerned me though, I see in your GitHub for this project you stated: Project frozen/final - This project is done from my side. It has been working for years but I switched to another solution so I won't update this anymore. and on your OpenHardware page: Update2: They have been running for about 2 years now mostly without problems. The only disadvantage is that my Mysensors network overall is quite "slow" (~1s reaction time). I am currently experimenting with Wifi RGBWW controllers (H801) so there wont be to many more updates to this project Which made me want to ask you what you are using now? It seems to me that those MagicHome type Wi-Fi (or RF) RGB controllers would be pretty hard to beat price wise, I don't think I could implement similar functionality (including packaging, etc.) for the same amount of money, and that's before even counting my time. Also I am still struggling with reliability of my MySensors network in general, but I hope to be able to still solve this as it seems that many others have been able to (but that is a different subject altogether).

@tlustoch The node is a very simple one. So I never considered boot loaders, as the node would not need changing sketches during it's lifetime. I have boot loading functionality on my other designs, this one is a minimal board. Any extra chip would beat the purpose of the word "minimal". It's a dumb node for a reason :-)

@pjr thank you, i am trying to learn signing for use :)

fine thx....

The step-up module didn't perform good enough using single AA-cell according to @axillent. The Micro board will be the first in line.

@VaZso i see 0-85 channel and i see most is silent , but my controller and gateway is 1m distance with router (because controller connect with lan cable to router) anyway thank you. i think this is related to just chinese radio...

@mainali said: Can you post the link to the updated code and the instruction of using NRF with ethernet module. I think everything you need to know is described here -> http://www.mysensors.org/build/ethernet_gateway

With the BME280 voltage regulator removed, I powered it stand-alone using a 3.3V bench power supply. Using Dave Jones's uCurrent in conjunction with a Fluke 87V multimeter, I measure the standby current at a mere 155 nanoamps. I had planned to power it from pins on the atmega328p and then powering it down between measurements, but at 155na I'm not sure it even matters, provided it's being powered from a battery. :smile: On the other hand, if the entire mote is being powered from a capacitor that's charged from solar energy that's harvested from only weak ambient indoor light.... I guess in that scenario it might depend on the relative leakage rate of the capacitor that's used for the mote's energy storage as to whether or not it's worth fussing about.

@Mufasa Yes, you can make custom names and groups of your devices. https://home-assistant.io/getting-started/devices/ Also read the blog post on customizing icons from version 0.8.

Hello, I use a My Sensors 2.0 version of "Multisensor node using @ceech board" but I have this error: TSP:MSG:SEND 5-5-0-0 s=255,c=3,t=11,pt=0,l=12,sg=0,ft=1,st=ok:JMP-LightLux TSP:MSG:SEND 5-5-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=ok:1.0 TSP:MSG:SEND 5-5-0-0 s=10,c=0,t=13,pt=0,l=0,sg=0,ft=0,st=ok: TSP:MSG:SEND 5-5-0-0 s=11,c=0,t=13,pt=0,l=0,sg=0,ft=0,st=ok: TSP:MSG:SEND 5-5-0-0 s=1,c=0,t=16,pt=0,l=0,sg=0,ft=0,st=ok: Request registration... TSP:MSG:SEND 5-5-0-0 s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=ok:2 TSP:MSG:READ 0-0-5 s=255,c=3,t=27,pt=1,l=1,sg=0:1 Node registration=1 Init complete, id=5, parent=0, distance=1, registration=1 BH1750 lux: 387TSP:MSG:SEND 5-5-0-0 s=1,c=1,t=37,pt=3,l=2,sg=0,ft=0,st=ok:387 Batt: 3.74V ; 414.08mA Solar: 0.00V ; 0.00 mA; charge: Yes BattPct: 61% TSP:MSG:SEND 5-5-0-0 s=10,c=1,t=38,pt=7,l=5,sg=0,ft=0,st=ok:3.738 TSP:MSG:SEND 5-5-0-0 s=10,c=1,t=39,pt=7,l=5,sg=0,ft=0,st=ok:0.414 TSP:MSG:SEND 5-5-0-0 s=11,c=1,t=38,pt=7,l=5,sg=0,ft=0,st=ok:0.000 TSP:MSG:SEND 5-5-0-0 s=11,c=1,t=39,pt=7,l=5,sg=0,ft=0,st=ok:0.000 !TSP:MSG:SEND 5-5-0-0 s=255,c=3,t=0,pt=1,l=1,sg=0,ft=0,st=fail:61 after that the node doesn't send data to gateway. Do you have some ideas to solve the problem? thanks

Does anyone with a Vera2 have that file?