Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

💬 NRF52 Gateway -(RFM69-option)

openhardware.io last edited by openhardware.io

https://www.openhardware.io/view/575/NRF52-Gateway-RFM69-option
Reply Quote 0
1 Reply Last reply
canossa last edited by

Hey, after some months what's your opinion abouts the gateway?
You still prefer the nrf52 instead of the rfm69?
Reply Quote 0
1 Reply Last reply
Omemanti last edited by @canossa

@canossa Sorry for the late response.

yeah, since is so compact and you can get it for relatively cheap I opted in for the NRF52.

For home automation, I merged MySensors with Domoticz and it works for months now.
https://forum.mysensors.org/topic/7836/what-did-you-build-today-pictures/738
Reply Quote 0
1 Reply Last reply

gateway 101 rfm69 60 nrf52832 22 e73-2g4m04s 4 ebyte 2

3
Posts

1991
Views

Log in to reply

Suggested Topics

MQTT Gateway + wi-fi instead of ethernet
Controllers • gateway mqtt wi-fi • • vladimir

4

0
Votes

4
Posts

2949
Views

Although it should not be too difficult to make the MQTT Gateway with WiFi work on hardware and software level it is a bad idea on system level: WiFi and MySensensor NRF24L01+ use the same 2.4 GHz band and with the antennas close a transmit from one will block the other and vice-versa.
Is MQTT Necessary? or, Use Case for MQTT?
Controllers • gateway mqtt openhab mqtt openhab • • TRS-80

18

0
Votes

18
Posts

8565
Views

@UglyKidJoe I have been using OpenHAB and MQTT for a number of years now. The reason for using MQTT and not just a serial connection from the MySensors GW is partly the flexibility as many have stated previously here. Easy to test, using e.g. the mqtt.fx tool. If you want to know what is going on you simply connect to the MQTT stream and "snoop" on the messages. Another reason is that I am running three geographical sites on one OH installation. OH is running on a NUC at my home. There is also an MQTT GW here. Two other My Sensors MQTT-GW are running remotely in two summer houses. The three GW connect over internet to a cloud-based MQTT broker and OH connects to the same broker. In that way I do not have to open any ports into my home network for access should I have had a local MQTT-broker at home.
SmartSleep a feature of the Gateway
Feature Requests • gateway openhab smartsleep • • strangeoptics

3

0
Votes

3
Posts

1881
Views

Nice. Didn't know that. But still it would be a great feature for the gateway to give every one the feature of smartSleep despite the controller.
💬 RFM69 - 8 relays board
OpenHardware.io • rfm69 relay • • openhardware.io

1

0
Votes

1
Posts

895
Views

No one has replied
💬 Usb serial Mysensors Gateway
OpenHardware.io • mysensors gateway mysensor passerelle de mysensors • • openhardware.io

1

0
Votes

1
Posts

260
Views

No one has replied
💬 RFM69 - 8 Dimmer output
OpenHardware.io • rfm69 dimmer • • openhardware.io

3

0
Votes

3
Posts

1362
Views

Not yet ! In fact, the interrupt must be short enough and fast enough to be sure to not miss the RFM69 interrupts. The code for 8 dimmers will not be really more complicated : in fact, each time we got a zero cross, we must set a timer to zero, and then wait the good amount of milliseconds to turn on the needed outputs. So, yes, we'll have an interrupts each 10ms (each time the wave crosses the zero, to be precise !), but I think all we have to do in the interrupt handler is set the timer to zero (or to micros() ...) and then on the main loop, wait the good amount of time for each output before setting them ON. Seems simple on paper, perhaps it will not work on the chip.... In facts, my main concern is : will the RFM interrupt be short enough to not disturb the zero crossing interrupt ? Although, not yet tested the RFM : do we NEED the interrupt pin ? Can't we poll frequently the RFM?
Multiple virtual nodes on a gateway
Troubleshooting • gateway serial gateway temperature & humidity sensor node id • • pvoj

10

0
Votes

10
Posts

1047
Views

@nca78 about my gateways: an old gateway running on MySensors 1.5 for years now. There are several nodes and sensors connected through it like temperature sensors, relays, switches. It controls my heating system with heat pump, buffering, 18 circles of floor heating, garden irrigation, alarm system, and some lights just for fun. the new gateway is a gateway to a Bluetooth network. Since MySensors has a great serial API and I have some experience with it I preferred to use it without a radio. I also think that it will be an interesting way of development and it could help to make MySensors even more popular. I had an idea to fork the library but unfortunately I don't have the experience and time to make it in good quality. But I'm sure letting developers to build connectors to different protocols is a very good idea. Catching Bluetooth messages from the air and decode them (with some reverse engineering) to send it through the MySensors gateway is relatively simple compared to the bidirectional communications. Processing some simple sensor data is a good first step.
Have anyone experienced MySensors gateway with GPRS(MQTT)?
General Discussion • gateway gsm gprs tinygsm sim800l • • jkandasa

2

0
Votes

2
Posts

1330
Views

@jkandasa I just finished a Gateway build with TinyGSM. You can find it here: https://www.openhardware.io/view/567/MySensors-GSM-Gateway

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Copyright 2019 Sensnology | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1