💬 Sensebender Gateway

[Disca]

Few things about the software side of this. When you plug it into your computer it appears as a "Sensebender GW", with a custom USB VID/PID. You have to override the drivers and use the "Atmel Corp. EDBG CMSIS-DAP" serial port drivers or you will have no serial port at all to communicate with the board.

Second issue, with the latest Arduino software (1.8.1), and the MySensors SAMD board package installed and MySensor library installed you get an error relating to a missing core "arduino:arduino". Solution to that one is to install the main Arduino SAMD board package which adds the necessary libraries. Secondly, after doing that you will now get another error regarding a missing "Sam.h" file, to fix that you have to manually edit the platform.txt file in "\AppData\Local\Arduino15\packages\MySensors\hardware\samd\1.0.3" with the contents of the one from "\AppData\Local\Arduino15\packages\arduino\hardware\samd\1.6.11" - just being careful to copy over the name and version lines from the top of the Mysensors platform.txt file. After that you are good to go and can finally program the board or get some data out of it

[tbowmo]

We are preparing a new release of the board definitions for our samd. Which fixes the issues with arduino samd 1.6.11.

It should also contain a driver .inf file for Windows 7/8, for those that needs it (it's not needed on Linux, mac or Windows 10). I had completely forgotten that windows usually needs this inf file to operate correct (I have been using Linux the last 17 years for all my private projects)

I hope the package will be out tomorrow (sunday) , as I just need to do a couple of tests to verify things.

[Viktor Zeman]

Do you have any example sketch for this gateway? I want to use in my GW radio + wifi module.

[tbowmo]

@Viktor-Zeman

It only support wired ethernet, and USB. For wifi we have ESP8266 gateways instead.

There are example sketches available in mysensors (see SensebenderGatewaySerial, or just plain GatewayW5100 would work if it's just ethernet module that you want to use)

[Disca]

@tbowmo Great, took a an hour or two to work out what was going on. Not used MySensors before so presumed it was something I was doing wrong. I have an RFM69HW soldered on the sensebender GW now with the serial sketch loaded and it appears to be working!

[tbowmo]

for info, a new Mysensors SAMD board definition file have been released (1.0.4)

Includes the following changes:
Arduino SAMD 1.6.11 supported (the latest arduino board definitions for SAMD)
Various bits and pieces regarding pin definitions are fixed (a couple of missing defines)
Windows driver .inf file added.

[Disca]

@tbowmo Compiles fine now with 1.0.4, not convinced the drivers are being automatically picked up though. I can force install them by selecting the inf but presumably you want it automatic when someone plugs in the gateway?

I notice in the arduino SAMD package they have a post-install.bat to seemingly install the inf file - possibly needed?

It could also be that i've just messed things up with my manual driver install stuff yesterday. I'm on Windows 7 by the way.

[Disca]

@tbowmo Also, I notice on Linux (Raspberry Pi 3 running Debian) the device appears as an ACM device rather than the usual TTY device that some might expect. It works fine though so no issues but may confuse alot of people - worth making a note somewhere.

[MLs]

@tbowmo

(for info, a new Mysensors SAMD board definition file have been released (1.0.4))

Where?

[Fabien]

@MLs reload board definition from IDE

I have a little annoying bug : I can't reset de gateway. When resetting, I loose communication with my computer (linux) same after loading a new sketch (last version with IDE 1.8.1 and def 1.0.4))

[13727.746445] usb 1-1: new full-speed USB device number 9 using xhci_hcd
[13727.892970] usb 1-1: New USB device found, idVendor=1209, idProduct=6949
[13727.892974] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[13727.892977] usb 1-1: Product: Sensebender GW
[13727.892980] usb 1-1: Manufacturer: MySensors.org
[13727.895690] cdc_acm 1-1:1.0: ttyACM1: USB ACM device
[13749.066589] usb 1-1: USB disconnect, device number 9

So I can't check debug messages from init.

[tbowmo]

@MLs

Check out the setup instructions here

and perhaps this

[tbowmo]

@Fabien

Are you using it as an ethernet gw, or standard serial gw? If serial GW, then the gateway waits until something connects to the serial device

The ethernet gw doesn't wait for something to connect. But you can hack the core, change hwInit() function in MyHwSAMD.cpp:

original

void hwInit()
{
        MY_SERIALDEVICE.begin(MY_BAUD_RATE);
#if defined(MY_GATEWAY_SERIAL)
        while (!MY_SERIALDEVICE) {}
#endif
        Wire.begin();
}

modify to this

void hwInit()
{
        MY_SERIALDEVICE.begin(MY_BAUD_RATE);
        while (!MY_SERIALDEVICE) {}
        Wire.begin();
}

It will make the gateway halt the initialization until something connects to the USB device.

Be advised, that if you don't have it connected to a computer, then it will not start up correctly.. That is why you need to hack the core to enable it..

[MLs]

@tbowmo

When I try to upload sketch

Arduino:1.8.0 (Windows 10), Kort:"Arduino/Genuino Zero (Native USB Port)"

Sketch uses 46488 bytes (17%) of program storage space. Maximum is 262144 bytes.
No device found on COM4
An error occurred while uploading the sketch
Invalid version found: 1.04
Invalid version found: 1.04

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.

When I use the serial monitor

0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGS--,VER=2.1.0
0;255;3;0;9;TSF:LRT:OK
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
0;255;3;0;14;Gateway startup complete.
0;255;0;0;18;2.1.0
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
0;255;3;0;9;TSF:MSG:READ,27-27-0,s=0,c=1,t=1,pt=7,l=5,sg=0:45.6
27;0;1;0;1;45.6
0;255;3;0;9;TSF:MSG:READ,23-23-0,s=1,c=1,t=0,pt=7,l=5,sg=0:8.4
23;1;1;0;0;8.4
0;255;3;0;9;TSF:MSG:READ,23-23-0,s=1,c=1,t=0,pt=7,l=5,sg=0:8.3
23;1;1;0;0;8.3
0;255;3;0;9;TSF:MSG:READ,23-23-0,s=0,c=1,t=1,pt=7,l=5,sg=0:51.8
23;0;1;0;1;51.8
0;255;3;0;9;TSF:MSG:READ,22-22-0,s=1,c=1,t=0,pt=7,l=5,sg=0:3.4
22;1;1;0;0;3.4
0;255;3;0;9;TSF:MSG:READ,23-23-0,s=0,c=1,t=1,pt=7,l=5,sg=0:52.0
23;0;1;0;1;52.0
0;255;3;0;9;TSF:MSG:READ,22-22-0,s=1,c=1,t=0,pt=7,l=5,sg=0:3.5
22;1;1;0;0;3.5
0;255;3;0;9;TSF:MSG:READ,23-23-0,s=1,c=1,t=0,pt=7,l=5,sg=0:8.2
23;1;1;0;0;8.2
0;255;3;0;9;TSF:MSG:READ,23-23-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
0;255;3;0;9;TSF:MSG:BC
0;255;3;0;9;TSF:MSG:FPAR REQ,ID=23
0;255;3;0;9;TSF:PNG:SEND,TO=0
0;255;3;0;9;TSF:CKU:OK
0;255;3;0;9;TSF:MSG:GWL OK
0;255;3;0;9;!TSF:MSG:SEND,0-0-23-23,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0
0;255;3;0;9;TSF:MSG:READ,23-23-0,s=0,c=1,t=1,pt=7,l=5,sg=0:52.4
23;0;1;0;1;52.4
0;255;3;0;9;TSF:MSG:READ,22-22-0,s=1,c=1,t=0,pt=7,l=5,sg=0:3.4
22;1;1;0;0;3.4
0;255;3;0;9;TSF:MSG:READ,23-23-0,s=1,c=1,t=0,pt=7,l=5,sg=0:8.1
23;1;1;0;0;8.1

I USE IDE 1.80

Which card should I choose to get upload sketch on GW

//Mattias

[tbowmo]

@MLs

have you installed the mysensors board files? And chosen the Sensebender Gateway as target platform?

(Seems that you are using Arduino/Genuino Zero as target?)

[Fabien]

@tbowmo I'm using the serial sketch.
I have few issues (I think) :

• when I want to upload a new sketch, first time after powering by computer, every led goes off and SBGW seems to be disconnected. When I unplug/plug, no led are on or blink, but detection is ok and I can upload a firmware.
• When I press RESET after connecting SBGW on my computer, all led goes off and SBGW disconnect.

And it doesn't seems to wait when I plug computer, led start blinking ...

[tbowmo]

@Fabien

Is it windows or linux? Linux (ubuntu) have a bad habit of letting modem manager snatch any ACM devices that is connected to the computer.

[MLs]

@tbowmo

Yes, I have installed MYSensors boards but find only micro

So therefore, I tried another card.

//Mattias

[MLs]

@MLs

I found the problem myself. Had just installed Micro

[Fabien]

@tbowmo said in Sensebender Gateway:

modem manager snatch any ACM devices

Yes it's ubuntu ... Do you know how to avoid this ? udev ?

[Fabien]

Ok :

sudo apt-get --purge remove modemmanager

[MLs]

@tbowmo

Hi i get same error whit Sensebender Ga

Arduino:1.8.0 (Windows 10), Kort:"Sensebender Gateway"

Build options changed, rebuilding all
Sketch uses 46720 bytes (17%) of program storage space. Maximum is 262144 bytes.
No device found on COM4
An error occurred while uploading the sketch
Invalid version found: 1.04
Invalid version found: 1.04

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.```

No device found on COM4
But serial monitor works fine with COM4

//Mattias

[Disca]

@MLs In Device Manager what com port is assigned to the sensebender GW? Have you manually installed the inf file?

com4 is likely the last com port you used in the arduino interface not the one assigned to the GW.

[MLs]

@Disca

No, I have not installed or selected com port.
Device Manager COM4
As I understood it so Windows 10 would fix everything, right?

//Mattias

[Fabien]

@tbowmo : It's better for seeing debug from start.
But there is 2 bugs :

• When you want to upload sketch. /dev/ttyACM0 disapear (and D4 goes off) afterunplu/plug it works for uploading sketch (D4 off) but at the end of uplaod ArduinoIDE makes a soft reset and /dev/ttyACM0 disapear. Works fine after plus/unplug (D4 ON)
• When pressing reset /dev/ttyACM0 disapear (and D4 goes off). Works fine after plug/unplug

[Disca]

@MLs mmm not sure then, it works for me on Windows 7 with 1.8.1 (slightly newer version?)

[tbowmo]

@MLs

I don't have windows installed, so I'm sorry that I can't help with windows specifics.

[MLs]

@tbowmo

Now, I think it feels like hardware failure more than software errors. Will try tomorrow on my second computer with Windows 7 and see if there is any difference.

//Mattias

[tbowmo]

@Fabien

I added a couple of udev rules, to stop modemmanager take control over the device

ACTION!="add|change|move", GOTO="local_usb_device_blacklist_end"
SUBSYSTEM!="usb", GOTO="local_usb_device_blacklist_end"
ENV{DEVTYPE}!="usb_device",  GOTO="local_usb_device_blacklist_end"

ATTRS{idVendor}=="1209", ENV{ID_MM_DEVICE_IGNORE}="1"

LABEL="local_usb_device_blacklist_end"

Add the above to this file /etc/udev/rules.d/mysensors.rules

As the USB is native in the arm processor, then it will re-enumerate on the USB port whenever a reset condition occurs. When you press the reset button it will act as a unplug / plug operation (you can see this in dmesg)

When uploading to the gateway, it will reset itself to enter bootloader.. The bootloader will have another VID/PID combo (VID:1209, PID:6448) than during normal operation (VID:1209, PID:6449).

I have never seen the problems that you are having, where you need to fysically unplug / plug the device, after you have pressed the reset button (or uploaded a new firmware). And I have uploaded firmware (and pressed the reset button) quite some times

Also please note, that if you double tap the reset button, the gateway will enter bootloader mode, and wait for a new sketch to be sent.

[Fabien]

@tbowmo : Same with udev rules (but this file is not necessary because modemmanger is not installed).
I try to power SBGW with usb, D4 goes ON. After pressing reset, D4 goes OFF and never goes on (I must unplug/plu usb power). Do you have the same with your board ? Perhaps a problem with bootloader ?

[tbowmo]

@Fabien

D4 is the yellow LED, and the only place it is used is in the onboard selftest routine.

In my setup, D5 turns on when plugging in the device. If I hit reset one time, it momentarily switches off D5, and then back on. if I hit reset twice, it stays off (bootloader is activated)

The above is done on my RFM69 debug gateway, so the sketch is for RFM69, but otherwise a standard SensebenderGatewaySerial sketch

Have you checked dmesg, when plugging in, and when hitting the reset button?

Have you tried with another USB cable? Have you tried with another computer?

[Fabien]

I try with 2 different USB cable and 2 computer (1 laptop and 1 desktop). Same problem. With a charger too. And sorry for the mistake, it's D5 (orange)
On log

[ 4788.031324] usb 1-8: USB disconnect, device number 6

[Fabien]

Thank you @scalz !
You must have a very well calibrated printer to print it correctly. First try fails (oozing due to overtemp)
Other side tomorrow !

[MLs]

@Disca

Where did you find the drivers for sensebender GW for Windows 7?

//Mattias

[tbowmo]

@MLs

Check the product page on mysensors.org

https://www.mysensors.org/hardware/sensebender-gateway

[tbowmo]

@Fabien

D5 is used by arduino to signal USB serial rx/TX activity.

Can you post the log lines from dmesg, from when you insert the usb cable, to after you have pressed the reset button?

[MLs]

@tbowmo

I tried to update the drivers in Device Manager / sense bender GW but it failed to install the computer said.

Therefore, I asked one who wrote that he was using Windows 7

//Mattias

[scalz]

@MLs
I'm also still using win7 x64 for my dev and that worked for me.

Auto install through the Device Manager does not work, nor right-clicking and installing the .inf through Explorer.

You have to force the install and select the location of the .inf in Device Manager. Then it will ask you if you agree about the driver supplier. Of course you're! And you should be able to see it in Device Manager.

[Dany]

There are example program for W5100? The original GatewayW5100 program uses SOFTSPI, different NRF CE/CSN pins? Will work with this hardware properly?

[MLs]

@scalz

Heh've tried both in the device manager and manually. Device Manager, I get an error message.

And manually, nothing happens.

//Mattias

[scalz]

@MLs
yep that's what i explained.
you need to force it in Device Manager. How you're doing in Device manager actually is rather auto, imho
You can try in Device manager to right click on the bad detected device, here Sensebender Gw, and in properties, update driver. At a moment, it should prompt an "Open file" Dialog box (you need to choose the right option in the dialog) and then select your .inf file. And it will ask if you're ok to install a driver from a third party.

[tbowmo]

@Dany

The standard GatewayW5100 example sketch will work on the sensebender gateway. There are conditional compile statements in that sketch, that disables softspi when compiling to the gateway target, and use a hardware SPI instead.

Remember to choose the correct target in your Arduino IDE

[scalz]

@MLs
Okay, simpler, forget what i told you, and follow my steps below. I've unstalled mine to show you
Then if it can be useful for others. Nothing fancy here, it can be used for lot of others drivers.

Step 1: plugin the GW, as you can see it's not detected, and no additional com port.

Step 2: right clic, and update driver

Step 3: click on the 2nd option for searching a driver on your machine

Step 4: Again 2nd option here (you want to search for a driver on your computer)

Step 5: This is a Virtual Serial Com port needed for the GW. So choose COM/LPT for the driver type

Step 6: Now it is asking where the driver (.inf) is stored

Step 7: You can now see that Windows knows what this is about. And tells you this driver is not "signed". No problem we know @tbowmo has done a great job. So, Next!

Step 8: Windows here warns again, saying he doesn't know this driver, so it may not work well. No way, it will work well Click "Yes" to install it.

Step 9: Looks good

Step 10: Tada! Here you can see now the GW is well detected and setup on COM port 24

I can't do better!
I think you'll get it

[MLs]

@scalz

Thanks for a super instruction but it is the file itself that the computer says from. It says that the folder contains the no driver

And the driver in the folder I chose I downloaded here

https://github.com/mysensors/ArduinoHwSAMD/blob/master/driver/mysensors-samd.inf

// Mattias

[MLs]

@MLs

When I downloaded the drivers so I make the following step.
Right-click at the file and save target as.

//Mattias

[hek]

On the raw file?

https://raw.githubusercontent.com/mysensors/ArduinoHwSAMD/master/driver/mysensors-samd.inf

[MLs]

@hek

https://github.com/mysensors/ArduinoHwSAMD/tree/master/driver

I click on the link below the folder drivers

//Mattias

[hek]

No, that will download a github html page.

Use the link I posted (and save as). It will be the raw content.

[MLs]

@hek

I'll try it tomorrow is not so strange that it did not work for me then.

//Mattias

[MLs]

@hek

Now, I also got the computer to recognize the card. Thanks for all help.

The problem was that even when I used save as, the computer renaming the file as a .txt file "mysensors-samd.inf.txt" and not a "mysensors-samd.inf"

Again, thanks for all the help.

//Mattias

[meddie]

Hi together,

i have some questions to you! I bought a sensebender gateway and a w5100 Ethernet Modul, but i cant get it to work. When i upload the Gateway5100 Sketch and put my yip address in it, then the GW is booting up i get some Data on the serial port but i cant ping the configured ip address. Then i tried to config via DHCP and see that the GW dont get an IP Address.
And when i connect the NRF24 Modul then it seems that the GW is not bootin up anymore because i dont get any data on serial port.
i need your help. Thanks a lot in advance

[tbowmo]

@meddie

Could you please post the logs that you get on the serial port, when the W5100 is attached?

Do you get anything on the serial port if you configure the sensebender to be a serial gateway, and only add a NRF24 module to it?

[meddie]

Hi tbowmo,

with the gatewayw5100 Sketch i get every 10 seconds 5 lines output on serial monitor:
The sketch is default i changed only the ip adress

0;255;3;0;9;TSM:FAIL:RE-INIT
0;255;3;0;9;TSM:INIT
0;255;3;0;9;!TSM:INIT:TSP FAIL
0;255;3;0;9;TSM:FAIL:CNT=3
0;255;3;0;9;TSM:FAIL:PDT
0;255;3;0;9;TSM:FAIL:RE-INIT
0;255;3;0;9;TSM:INIT
0;255;3;0;9;!TSM:INIT:TSP FAIL
0;255;3;0;9;TSM:FAIL:CNT=4
0;255;3;0;9;TSM:FAIL:PDT
0;255;3;0;9;TSM:FAIL:RE-INIT
0;255;3;0;9;TSM:INIT
0;255;3;0;9;!TSM:INIT:TSP FAIL
0;255;3;0;9;TSM:FAIL:CNT=5
0;255;3;0;9;

i dont know why, but i just uploaded the sensebenderserialgateway sketch and now i get this output:

0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGS--,VER=2.1.1
0;255;3;0;9;TSF:LRT:OK
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
0;255;3;0;14;Gateway startup complete.
0;255;0;0;18;2.1.1
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;

the NRF Module is connected! Now i need to get the w5100 module to work.

[meddie]

Ok i just connected the W5100 and NRF24 Module and uploaded the GatewayW5100 Sketch and when the upload is done after reset i dont get any output on serial monitor.
The orange, green and red led are lighting.

When i upload the SensebenderGatewaySerial then i get output on serial monitor. It think the problem must be the w5100. But what going wrong?

[tbowmo]

@meddie

Is it the standard GatewayW5100 sketch, without modifications, from the mysensors examples?

If you have done any modifications to the sketch, then please post your modified sketch here.

[meddie]

i have only changed the ip adress
here is the sketch:

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - Henrik EKblad
 * Contribution by a-lurker and Anticimex,
 * Contribution by Norbert Truchsess <norbert.truchsess@t-online.de>
 * Contribution by Tomas Hozza <thozza@gmail.com>
 *
 *
 * DESCRIPTION
 * The EthernetGateway sends data received from sensors to the ethernet link.
 * The gateway also accepts input on ethernet interface, which is then sent out to the radio network.
 *
 * The GW code is designed for Arduino 328p / 16MHz.  ATmega168 does not have enough memory to run this program.
 *
 * LED purposes:
 * - To use the feature, uncomment MY_DEFAULT_xxx_LED_PIN in the sketch below
 * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
 * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
 * - ERR (red) - fast blink on error during transmission error or recieve crc error
 *
 * See http://www.mysensors.org/build/ethernet_gateway for wiring instructions.
 *
 */

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Enable gateway ethernet module type
#define MY_GATEWAY_W5100

// W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
//#define MY_W5100_SPI_EN 4

// Enable Soft SPI for NRF radio (note different radio wiring is required)
// The W5100 ethernet module seems to have a hard time co-operate with
// radio on the same spi bus.
#if !defined(MY_W5100_SPI_EN) && !defined(ARDUINO_ARCH_SAMD)
#define MY_SOFTSPI
#define MY_SOFT_SPI_SCK_PIN 14
#define MY_SOFT_SPI_MISO_PIN 16
#define MY_SOFT_SPI_MOSI_PIN 15
#endif

// When W5100 is connected we have to move CE/CSN pins for NRF radio
#ifndef MY_RF24_CE_PIN
#define MY_RF24_CE_PIN 5
#endif
#ifndef MY_RF24_CS_PIN
#define MY_RF24_CS_PIN 6
#endif

// Enable to UDP
//#define MY_USE_UDP

#define MY_IP_ADDRESS 10,0,0,253   // If this is disabled, DHCP is used to retrieve address
// Renewal period if using DHCP
//#define MY_IP_RENEWAL_INTERVAL 60000
// The port to keep open on node server mode / or port to contact in client mode
#define MY_PORT 5003

// Controller ip address. Enables client mode (default is "server" mode).
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254

// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN  3

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Flash leds on rx/tx/err
// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 7  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  8  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  9  // Transmit led pin


#if defined(MY_USE_UDP)
#include <EthernetUdp.h>
#endif
#include <Ethernet.h>
#include <MySensors.h>


void setup()
{
}

void loop()
{
}```

[jeti]

So I think i have a maybe already solved issue, but I can not get int working...
In Arduino IDE 1.8.1 this is the error during compiling:

"Local\Arduino15\packages\arduino\hardware\samd\1.6.12\cores\arduino/Arduino.h:48:17: fatal error: sam.h: No such file or directory"

• I have the MySensors SAMD boards installed, so Sensbender Gateway is availabe

• Arduino SAMD boards are also installed

• I have installed the "M0" boards

• Running windows 10 so no need for the inf file, is this correct?

what am I missing?

thanks in advance!

[tekka]

@jeti SAMD board defs 1.6.12 are currently not supported (PR filed) - you need to downgrade to 1.6.11 until the PR is merged.

[jeti]

@tekka thanks! that did the trick!

[tekka]

@jeti MySensors SAMD board defs updated to 1.0.5, supporting SAMD board defs 1.6.12

[TheoL]

It's has been a long time since I've posted on this forum.Today I received a note form the postal service that a package from a foreign country has arrived at my local postal office. Can't wait until tomorrow, just to see this beauty.

Now I have to find some time to get it running ;-(

[tekka]

@TheoL yeah, almost 4mo ago - good to have you back

[TheoL]

@tekka life is really busy. But I'm working on some new MySensors idea's I'd like to try out. But for now on my way to the postal office. Can't wait.

[tmn103]

Is there any way of getting the MQTT Ethernet gateway working on this yet?

[tbowmo]

@tmn103

I haven't tried myself, but it should be the standard GatewayW5100MQTTClient sketch, without modifications. (the GatewayW5100 sketch is running without modifications already)

[tmn103]

Just tried the MQTT gateway sketch and got some strange behaviour.

Seems to pick up one of the nodes, but can't get an ip address or mqtt connection.

Any ideas on what to try?

0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
IP: 0.0.0.0
0;255;3;0;9;Attempting MQTT connection...
0;255;3;0;9;TSF:MSG:READ,113-113-0,s=0,c=1,t=0,pt=7,l=5,sg=0:20.8
0;255;3;0;9;TSF:MSG:READ,113-113-0,s=0,c=1,t=0,pt=7,l=5,sg=0:20.8
IP: 255.255.255.255
0;255;3;0;9;Attempting MQTT connection...
IP: 0.0.0.0
0;255;3;0;9;Attempting MQTT connection...
IP: 255.255.255.255
0;255;3;0;9;Attempting MQTT connection...
IP: 0.0.0.0
0;255;3;0;9;Attempting MQTT connection...
IP: 255.255.255.255
0;255;3;0;9;Attempting MQTT connection...
IP: 0.0.0.0

[tmn103]

Still can't get the mqtt gateway to work. Has anybody managed to?

[Fabien]

Just try standard GatewayW5100MQTTClient sketch. It works fine with RFM69HW
On your log you seems to have issue with your IP. Just my log :

0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
IP: 192.168.1.47
0;255;3;0;9;Attempting MQTT connection...
0;255;3;0;9;MQTT connected
0;255;3;0;9;Sending message on topic: mygateway1-out/0/255/0/0/18
0;255;3;0;9;TSF:MSG:READ,15-15-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
0;255;3;0;9;TSF:MSG:BC
0;255;3;0;9;TSF:MSG:FPAR REQ,ID=15
0;255;3;0;9;TSF:PNG:SEND,TO=0
0;255;3;0;9;TSF:CKU:OK
0;255;3;0;9;TSF:MSG:GWL OK
0;255;3;0;9;TSF:MSG:SEND,0-0-15-15,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
0;255;3;0;9;TSF:MSG:READ,15-15-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
0;255;3;0;9;TSF:MSG:PINGED,ID=15,HP=1
0;255;3;0;9;TSF:MSG:SEND,0-0-15-15,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
0;255;3;0;9;TSF:MSG:READ,15-15-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
0;255;3;0;9;Sending message on topic: mygateway1-out/15/3/1/0/16

[blacey]

@tmn103 said in Sensebender Gateway:

Just tried the MQTT gateway sketch and got some strange behaviour.

Seems to pick up one of the nodes, but can't get an ip address or mqtt connection.

Any ideas on what to try?

IP: 255.255.255.255
0;255;3;0;9;Attempting MQTT connection...
IP: 0.0.0.0

I would triple-check the IP addresses that you are using...

[meddie]

i have uploaded this securitypersonalizer.ino sketch:

/*
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 */
/**
 * @ingroup MySigninggrp
 * @{
 * @file SecurityPersonalizer.ino
 * @brief Security personalization sketch
 *
 * REVISION HISTORY
 *  - See git log (git log libraries/MySensors/examples/SecurityPersonalizer/SecurityPersonalizer.ino)
 */

/**
 * @example SecurityPersonalizer.ino
 * This sketch will personalize either none-volatile memory or ATSHA204A for security functions
 * available in the MySensors library.
 *
 * For ATSHA204A:
 * It will write factory default settings to the configuration zone
 * and then lock it.<br>
 * It will then either<br>
 * -# Generate a random value to use as a key which will be stored in
 * slot 0. The key is printed on UART (115200) in clear text for the user to be
 * able to use it as a user-supplied key in other personalization executions
 * where the same key is needed.
 * -# Use a user-supplied value to use as a key which will be stored in
 * slot 0.
 * Finally it will lock the data zone.
 *
 * By default, no locking is performed. User have to manually enable the flags that
 * turn on the locking. Furthermore, user have to send a SPACE character on serial
 * console when prompted to do any locking. On boards that does not provide UART
 * input it is possible to configure the sketch to skip this confirmation.
 * Default settings use ATSHA204A on @ref MY_SIGNING_ATSHA204_PIN.
 *
 * For Soft signing:
 * It will<br>
 * -# Generate a random value to use as a key which will be stored in EEPROM.
 * The key is printed on UART (115200) in clear text for the user to be ablle to
 * use it as a user-supplied key in other personalization executions where the same
 * key is needed.
 * -# Use a user-supplied value to use as a key which will be stored in EEPROM.
 * -# Generate a random value to use as a serial number which will be stored in EEPROM.
 * The serial number is printed on UART (115200) in clear text for the user to be ablle to
 * use it as a user-supplied serial number in other personalization executions where the
 * serial is needed (typically for a whitelist).
 * -# Use a user-supplied value to use as a serial which will be stored in EEPROM.
 *
 * For Encryption support:
 * -# Generate a random value to use as a AES key which will be stored in EEPROM.
 * The AES key is printed on UART (115200) in clear text for the user to be ablle to
 * use it as a user-supplied AES key in other personalization executions where the
 * AES key is needed (typically for RF encryption).
 * -# Use a user-supplied value to use as a AES key which will be stored in EEPROM.
 *
 * Personalizing EEPROM or ATSHA204A still require the appropriate configuration of the
 * library to actually have an effect. There is no problem personalizing EEPROM and
 * ATSHA204A at the same time. There is however a security risk with using the same
 * data for EEPROM and ATSHA204A so it is recommended to use different serial and HMAC
 * keys on the same device for ATSHA204A vs soft signing settings.
 *
 * Details on personalization procedure is given in @ref personalization.
 */

#include "sha204_library.h"
#include "sha204_lib_return_codes.h"
#define MY_CORE_ONLY
#include <MySensors.h>

// Doxygen specific constructs, not included when built normally
// This is used to enable disabled macros/definitions to be included in the documentation as well.
#if DOXYGEN
#define LOCK_CONFIGURATION
#define LOCK_DATA
#define SKIP_KEY_STORAGE
#define USER_KEY
#define SKIP_UART_CONFIRMATION
#define USE_SOFT_SIGNING
#define STORE_SOFT_KEY
#define USER_SOFT_KEY
#define STORE_SOFT_SERIAL
#define USER_SOFT_SERIAL
#define STORE_AES_KEY
#define USER_AES_KEY
#endif

/**
 * @def LOCK_CONFIGURATION
 * @brief Uncomment this to enable locking the configuration zone.
 *
 * It is still possible to change the key, and this also enable random key generation.
 * @warning BE AWARE THAT THIS PREVENTS ANY FUTURE CONFIGURATION CHANGE TO THE CHIP
 */
#define LOCK_CONFIGURATION

/**
 * @def LOCK_DATA
 * @brief Uncomment this to enable locking the data zone.
 *
 * It is not required to lock data, key cannot be retrieved anyway, but by locking
 * data, it can be guaranteed that nobody even with physical access to the chip,
 * will be able to change the key.
 * @warning BE AWARE THAT THIS PREVENTS THE KEY TO BE CHANGED
 */
//#define LOCK_DATA

/**
 * @def SKIP_KEY_STORAGE
 * @brief Uncomment this to skip key storage (typically once key has been written once)
 */
#define SKIP_KEY_STORAGE

/**
 * @def USER_KEY
 * @brief Uncomment this to skip key generation and use @ref user_key_data as key instead.
 */
//#define USER_KEY

/**
 * @def SKIP_UART_CONFIRMATION
 * @brief Uncomment this for boards that lack UART
 *
 * @b Important<br> No confirmation will be required for locking any zones with this configuration!
 * Also, key generation is not permitted in this mode as there is no way of presenting the generated key.
 */
//#define SKIP_UART_CONFIRMATION

/**
 * @def USE_SOFT_SIGNING
 * @brief Uncomment this to store data to EEPROM instead of ATSHA204A
 */
//#define USE_SOFT_SIGNING

/**
 * @def STORE_SOFT_KEY
 * @brief Uncomment this to store soft HMAC key to EEPROM
 */
//#define STORE_SOFT_KEY

/**
 * @def USER_SOFT_KEY
 * @brief Uncomment this to skip soft HMAC key generation and use @ref user_soft_key_data as HMAC key instead.
 */
//#define USER_SOFT_KEY

/**
 * @def STORE_SOFT_SERIAL
 * @brief Uncomment this to store soft serial to EEPROM
 */
//#define STORE_SOFT_SERIAL

/**
 * @def USER_SOFT_SERIAL
 * @brief Uncomment this to skip soft serial generation and use @ref user_soft_serial as serial instead.
 */
//#define USER_SOFT_SERIAL

/**
 * @def STORE_AES_KEY
 * @brief Uncomment this to store AES key to EEPROM
 */
//#define STORE_AES_KEY

/**
 * @def USER_AES_KEY
 * @brief Uncomment this to skip AES key generation and use @ref user_aes_key as key instead.
 */
//#define USER_AES_KEY

#if defined(SKIP_UART_CONFIRMATION) && !defined(USER_KEY)
#error You have to define USER_KEY for boards that does not have UART
#endif

#ifdef USER_KEY
/** @brief The user-defined HMAC key to use for personalization */
#define MY_HMAC_KEY 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
/** @brief The data to store in key slot 0 */
const uint8_t user_key_data[32] = {MY_HMAC_KEY};
#endif

#ifdef USER_SOFT_KEY
/** @brief The user-defined soft HMAC key to use for EEPROM personalization */
#define MY_SOFT_HMAC_KEY 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
/** @brief The data to store as soft HMAC key in EEPROM */
const uint8_t user_soft_key_data[32] = {MY_SOFT_HMAC_KEY};
#endif

#ifdef USER_SOFT_SERIAL
/** @brief The user-defined soft serial to use for EEPROM personalization */
#define MY_SOFT_SERIAL 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
/** @brief The data to store as soft serial in EEPROM */
const uint8_t user_soft_serial[9] = {MY_SOFT_SERIAL};
#endif

#ifdef USER_AES_KEY
/** @brief The user-defined AES key to use for EEPROM personalization */
#define MY_AES_KEY 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
/** @brief The data to store as AES key in EEPROM */
const uint8_t user_aes_key[16] = {MY_AES_KEY};
#endif

#ifndef USE_SOFT_SIGNING
const int sha204Pin = MY_SIGNING_ATSHA204_PIN; //!< The IO pin to use for ATSHA204A
atsha204Class sha204(sha204Pin);
#endif

/** @brief Print a error notice and halt the execution */
void halt()
{
	Serial.println(F("Halting!"));
	while(1);
}

#ifndef USE_SOFT_SIGNING
/**
 * @brief Write default configuration and return CRC of the configuration bits
 * @returns CRC over the configuration bits
 */
uint16_t write_config_and_get_crc()
{
	uint16_t crc = 0;
	uint8_t config_word[4];
	uint8_t tx_buffer[SHA204_CMD_SIZE_MAX];
	uint8_t rx_buffer[SHA204_RSP_SIZE_MAX];
	uint8_t ret_code;
	bool do_write;

	// We will set default settings from datasheet on all slots. This means that we can use slot 0 for the key
	// as that slot will not be readable (key will therefore be secure) and slot 8 for the payload digest
	// calculationon as that slot can be written in clear text even when the datazone is locked.
	// Other settings which are not relevant are kept as is.

	for (int i=0; i < 88; i += 4) {
		do_write = true;
		if (i == 20) {
			config_word[0] = 0x8F;
			config_word[1] = 0x80;
			config_word[2] = 0x80;
			config_word[3] = 0xA1;
		} else if (i == 24) {
			config_word[0] = 0x82;
			config_word[1] = 0xE0;
			config_word[2] = 0xA3;
			config_word[3] = 0x60;
		} else if (i == 28) {
			config_word[0] = 0x94;
			config_word[1] = 0x40;
			config_word[2] = 0xA0;
			config_word[3] = 0x85;
		} else if (i == 32) {
			config_word[0] = 0x86;
			config_word[1] = 0x40;
			config_word[2] = 0x87;
			config_word[3] = 0x07;
		} else if (i == 36) {
			config_word[0] = 0x0F;
			config_word[1] = 0x00;
			config_word[2] = 0x89;
			config_word[3] = 0xF2;
		} else if (i == 40) {
			config_word[0] = 0x8A;
			config_word[1] = 0x7A;
			config_word[2] = 0x0B;
			config_word[3] = 0x8B;
		} else if (i == 44) {
			config_word[0] = 0x0C;
			config_word[1] = 0x4C;
			config_word[2] = 0xDD;
			config_word[3] = 0x4D;
		} else if (i == 48) {
			config_word[0] = 0xC2;
			config_word[1] = 0x42;
			config_word[2] = 0xAF;
			config_word[3] = 0x8F;
		} else if (i == 52 || i == 56 || i == 60 || i == 64) {
			config_word[0] = 0xFF;
			config_word[1] = 0x00;
			config_word[2] = 0xFF;
			config_word[3] = 0x00;
		} else if (i == 68 || i == 72 || i == 76 || i == 80) {
			config_word[0] = 0xFF;
			config_word[1] = 0xFF;
			config_word[2] = 0xFF;
			config_word[3] = 0xFF;
		} else {
			// All other configs are untouched
			ret_code = sha204.sha204m_read(tx_buffer, rx_buffer, SHA204_ZONE_CONFIG, i);
			if (ret_code != SHA204_SUCCESS) {
				Serial.print(F("Failed to read config. Response: "));
				Serial.println(ret_code, HEX);
				halt();
			}
			// Set config_word to the read data
			config_word[0] = rx_buffer[SHA204_BUFFER_POS_DATA+0];
			config_word[1] = rx_buffer[SHA204_BUFFER_POS_DATA+1];
			config_word[2] = rx_buffer[SHA204_BUFFER_POS_DATA+2];
			config_word[3] = rx_buffer[SHA204_BUFFER_POS_DATA+3];
			do_write = false;
		}

		// Update crc with CRC for the current word
		crc = sha204.calculateAndUpdateCrc(4, config_word, crc);

		// Write config word
		if (do_write) {
			ret_code = sha204.sha204m_execute(SHA204_WRITE, SHA204_ZONE_CONFIG,
			                                  i >> 2, 4, config_word, 0, NULL, 0, NULL,
			                                  WRITE_COUNT_SHORT, tx_buffer, WRITE_RSP_SIZE, rx_buffer);
			if (ret_code != SHA204_SUCCESS) {
				Serial.print(F("Failed to write config word at address "));
				Serial.print(i);
				Serial.print(F(". Response: "));
				Serial.println(ret_code, HEX);
				halt();
			}
		}
	}
	return crc;
}

/**
 * @brief Write provided key to slot 0
 * @param key The key data to write
 */
void write_key(uint8_t* key)
{
	uint8_t tx_buffer[SHA204_CMD_SIZE_MAX];
	uint8_t rx_buffer[SHA204_RSP_SIZE_MAX];
	uint8_t ret_code;

	// Write key to slot 0
	ret_code = sha204.sha204m_execute(SHA204_WRITE, SHA204_ZONE_DATA | SHA204_ZONE_COUNT_FLAG,
	                                  0, SHA204_ZONE_ACCESS_32, key, 0, NULL, 0, NULL,
	                                  WRITE_COUNT_LONG, tx_buffer, WRITE_RSP_SIZE, rx_buffer);
	if (ret_code != SHA204_SUCCESS) {
		Serial.print(F("Failed to write key to slot 0. Response: "));
		Serial.println(ret_code, HEX);
		halt();
	}
}
#endif // not USE_SOFT_SIGNING

/** @brief Dump current configuration to UART */
void dump_configuration()
{
	uint8_t buffer[32];
#ifndef USE_SOFT_SIGNING
	Serial.println(F("EEPROM DATA:"));
#endif
	hwReadConfigBlock((void*)buffer, (void*)EEPROM_SIGNING_SOFT_HMAC_KEY_ADDRESS, 32);
	Serial.print(F("SOFT_HMAC_KEY | "));
	for (int j=0; j<32; j++) {
		if (buffer[j] < 0x10) {
			Serial.print('0'); // Because Serial.print does not 0-pad HEX
		}
		Serial.print(buffer[j], HEX);
	}
	Serial.println();
	hwReadConfigBlock((void*)buffer, (void*)EEPROM_SIGNING_SOFT_SERIAL_ADDRESS, 9);
	Serial.print(F("SOFT_SERIAL   | "));
	for (int j=0; j<9; j++) {
		if (buffer[j] < 0x10) {
			Serial.print('0'); // Because Serial.print does not 0-pad HEX
		}
		Serial.print(buffer[j], HEX);
	}
	Serial.println();
	hwReadConfigBlock((void*)buffer, (void*)EEPROM_RF_ENCRYPTION_AES_KEY_ADDRESS, 16);
	Serial.print(F("AES_KEY       | "));
	for (int j=0; j<16; j++) {
		if (buffer[j] < 0x10) {
			Serial.print('0'); // Because Serial.print does not 0-pad HEX
		}
		Serial.print(buffer[j], HEX);
	}
	Serial.println();
#ifndef USE_SOFT_SIGNING
	uint8_t tx_buffer[SHA204_CMD_SIZE_MAX];
	uint8_t rx_buffer[SHA204_RSP_SIZE_MAX];
	uint8_t ret_code;
	Serial.println(F("ATSHA204A DATA:"));
	for (int i=0; i < 88; i += 4) {
		ret_code = sha204.sha204m_read(tx_buffer, rx_buffer, SHA204_ZONE_CONFIG, i);
		if (ret_code != SHA204_SUCCESS) {
			Serial.print(F("Failed to read config. Response: "));
			Serial.println(ret_code, HEX);
			halt();
		}
		if (i == 0x00) {
			Serial.print(F("           SN[0:1]           |         SN[2:3]           | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j == 1) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		} else if (i == 0x04) {
			Serial.print(F("                          Revnum                         | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				Serial.print(F("   "));
			}
			Serial.println();
		} else if (i == 0x08) {
			Serial.print(F("                          SN[4:7]                        | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				Serial.print(F("   "));
			}
			Serial.println();
		} else if (i == 0x0C) {
			Serial.print(F("    SN[8]    |  Reserved13   | I2CEnable | Reserved15    | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j < 3) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		} else if (i == 0x10) {
			Serial.print(F("  I2CAddress |  TempOffset   |  OTPmode  | SelectorMode  | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j < 3) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		} else if (i == 0x14) {
			Serial.print(F("         SlotConfig00        |       SlotConfig01        | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j == 1) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		} else if (i == 0x18) {
			Serial.print(F("         SlotConfig02        |       SlotConfig03        | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j == 1) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		} else if (i == 0x1C) {
			Serial.print(F("         SlotConfig04        |       SlotConfig05        | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j == 1) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		} else if (i == 0x20) {
			Serial.print(F("         SlotConfig06        |       SlotConfig07        | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j == 1) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		} else if (i == 0x24) {
			Serial.print(F("         SlotConfig08        |       SlotConfig09        | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j == 1) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		} else if (i == 0x28) {
			Serial.print(F("         SlotConfig0A        |       SlotConfig0B        | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j == 1) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		} else if (i == 0x2C) {
			Serial.print(F("         SlotConfig0C        |       SlotConfig0D        | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j == 1) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		} else if (i == 0x30) {
			Serial.print(F("         SlotConfig0E        |       SlotConfig0F        | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j == 1) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		} else if (i == 0x34) {
			Serial.print(F("  UseFlag00  | UpdateCount00 | UseFlag01 | UpdateCount01 | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j < 3) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		} else if (i == 0x38) {
			Serial.print(F("  UseFlag02  | UpdateCount02 | UseFlag03 | UpdateCount03 | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j < 3) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		} else if (i == 0x3C) {
			Serial.print(F("  UseFlag04  | UpdateCount04 | UseFlag05 | UpdateCount05 | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j < 3) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		} else if (i == 0x40) {
			Serial.print(F("  UseFlag06  | UpdateCount06 | UseFlag07 | UpdateCount07 | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j < 3) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		} else if (i == 0x44) {
			Serial.print(F("                      LastKeyUse[0:3]                    | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				Serial.print(F("   "));
			}
			Serial.println();
		} else if (i == 0x48) {
			Serial.print(F("                      LastKeyUse[4:7]                    | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				Serial.print(F("   "));
			}
			Serial.println();
		} else if (i == 0x4C) {
			Serial.print(F("                      LastKeyUse[8:B]                    | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				Serial.print(F("   "));
			}
			Serial.println();
		} else if (i == 0x50) {
			Serial.print(F("                      LastKeyUse[C:F]                    | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				Serial.print(F("   "));
			}
			Serial.println();
		} else if (i == 0x54) {
			Serial.print(F("  UserExtra  |    Selector   | LockValue |  LockConfig   | "));
			for (int j=0; j<4; j++) {
				if (rx_buffer[SHA204_BUFFER_POS_DATA+j] < 0x10) {
					Serial.print('0'); // Because Serial.print does not 0-pad HEX
				}
				Serial.print(rx_buffer[SHA204_BUFFER_POS_DATA+j], HEX);
				if (j < 3) {
					Serial.print(F(" | "));
				} else {
					Serial.print(F("   "));
				}
			}
			Serial.println();
		}
	}
#endif // not USE_SOFT_SIGNING
}

/** @brief Sketch setup code */
void setup()
{
	// Delay startup a bit for serial consoles to catch up
	unsigned long enter = hwMillis();
	while (hwMillis() - enter < (unsigned long)500);
#ifndef USE_SOFT_SIGNING
	uint8_t tx_buffer[SHA204_CMD_SIZE_MAX];
	uint8_t rx_buffer[SHA204_RSP_SIZE_MAX];
	uint8_t ret_code;
	uint8_t lockConfig = 0;
	uint8_t lockValue = 0;
	uint16_t crc;
	(void)crc;
#else
	// initialize pseudo-RNG
	randomSeed(analogRead(MY_SIGNING_SOFT_RANDOMSEED_PIN));
#endif
	uint8_t key[32];
	(void)key;

	Serial.begin(115200);
	hwInit();
	Serial.println(F("Personalization sketch for MySensors usage."));
	Serial.println(F("-------------------------------------------"));

#ifndef USE_SOFT_SIGNING
	// Wake device before starting operations
	ret_code = sha204.sha204c_wakeup(rx_buffer);
	if (ret_code != SHA204_SUCCESS) {
		Serial.print(F("Failed to wake device. Response: "));
		Serial.println(ret_code, HEX);
		halt();
	}
	// Read out lock config bits to determine if locking is possible
	ret_code = sha204.sha204m_read(tx_buffer, rx_buffer, SHA204_ZONE_CONFIG, 0x15<<2);
	if (ret_code != SHA204_SUCCESS) {
		Serial.print(F("Failed to determine device lock status. Response: "));
		Serial.println(ret_code, HEX);
		halt();
	} else {
		lockConfig = rx_buffer[SHA204_BUFFER_POS_DATA+3];
		lockValue = rx_buffer[SHA204_BUFFER_POS_DATA+2];
	}
#endif

#ifdef STORE_SOFT_KEY
#ifdef USER_SOFT_KEY
	memcpy(key, user_soft_key_data, 32);
	Serial.println(F("Using this user supplied soft HMAC key:"));
#else
	// Retrieve random value to use as soft HMAC key
#ifdef USE_SOFT_SIGNING
	for (int i = 0; i < 32; i++) {
		key[i] = random(256) ^ micros();
		unsigned long enter = hwMillis();
		while (hwMillis() - enter < (unsigned long)2);
	}
	Serial.println(F("This value will be stored in EEPROM as soft HMAC key:"));
#else
	ret_code = sha204.sha204m_random(tx_buffer, rx_buffer, RANDOM_SEED_UPDATE);
	if (ret_code != SHA204_SUCCESS) {
		Serial.print(F("Random key generation failed. Response: "));
		Serial.println(ret_code, HEX);
		halt();
	} else {
		memcpy(key, rx_buffer+SHA204_BUFFER_POS_DATA, 32);
	}
	if (lockConfig == 0x00) {
		Serial.println(F("This value will be stored in EEPROM as soft HMAC key:"));
	} else {
		Serial.println(F("Key is not randomized (configuration not locked):"));
	}
#endif // not USE_SOFT_SIGNING
#endif // not USER_SOFT_KEY
	Serial.print("#define MY_SOFT_HMAC_KEY ");
	for (int i=0; i<32; i++) {
		Serial.print("0x");
		if (key[i] < 0x10) {
			Serial.print('0'); // Because Serial.print does not 0-pad HEX
		}
		Serial.print(key[i], HEX);
		if (i < 31) {
			Serial.print(',');
		}
	}
	Serial.println();
	hwWriteConfigBlock((void*)key, (void*)EEPROM_SIGNING_SOFT_HMAC_KEY_ADDRESS, 32);
#endif // STORE_SOFT_KEY

#ifdef STORE_SOFT_SERIAL
#ifdef USER_SOFT_SERIAL
	memcpy(key, user_soft_serial, 9);
	Serial.println(F("Using this user supplied soft serial:"));
#else
	// Retrieve random value to use as serial
#ifdef USE_SOFT_SIGNING
	for (int i = 0; i < 9; i++) {
		key[i] = random(256) ^ micros();
		unsigned long enter = hwMillis();
		while (hwMillis() - enter < (unsigned long)2);
	}
	Serial.println(F("This value will be stored in EEPROM as soft serial:"));
#else
	ret_code = sha204.sha204m_random(tx_buffer, rx_buffer, RANDOM_SEED_UPDATE);
	if (ret_code != SHA204_SUCCESS) {
		Serial.print(F("Random serial generation failed. Response: "));
		Serial.println(ret_code, HEX);
		halt();
	} else {
		memcpy(key, rx_buffer+SHA204_BUFFER_POS_DATA, 9);
	}
	if (lockConfig == 0x00) {
		Serial.println(F("This value will be stored in EEPROM as soft serial:"));
	} else {
		Serial.println(F("Serial is not randomized (configuration not locked):"));
	}
#endif // not USE_SOFT_SIGNING
#endif // not USER_SOFT_SERIAL
	Serial.print("#define MY_SOFT_SERIAL ");
	for (int i=0; i<9; i++) {
		Serial.print("0x");
		if (key[i] < 0x10) {
			Serial.print('0'); // Because Serial.print does not 0-pad HEX
		}
		Serial.print(key[i], HEX);
		if (i < 8) {
			Serial.print(',');
		}
	}
	Serial.println();
	hwWriteConfigBlock((void*)key, (void*)EEPROM_SIGNING_SOFT_SERIAL_ADDRESS, 9);
#endif // STORE_SOFT_SERIAL

#ifdef STORE_AES_KEY
#ifdef USER_AES_KEY
	memcpy(key, user_aes_key, 16);
	Serial.println(F("Using this user supplied AES key:"));
#else
	// Retrieve random value to use as key
#ifdef USE_SOFT_SIGNING
	for (int i = 0; i < 16; i++) {
		key[i] = random(256) ^ micros();
		unsigned long enter = hwMillis();
		while (hwMillis() - enter < (unsigned long)2);
	}
	Serial.println(F("This key will be stored in EEPROM as AES key:"));
#else
	ret_code = sha204.sha204m_random(tx_buffer, rx_buffer, RANDOM_SEED_UPDATE);
	if (ret_code != SHA204_SUCCESS) {
		Serial.print(F("Random key generation failed. Response: "));
		Serial.println(ret_code, HEX);
		halt();
	} else {
		memcpy(key, rx_buffer+SHA204_BUFFER_POS_DATA, 32);
	}
	if (lockConfig == 0x00) {
		Serial.println(F("This key will be stored in EEPROM as AES key:"));
	} else {
		Serial.println(F("Key is not randomized (configuration not locked):"));
	}
	
.... i have cut the rest of code because its to long to post here complete ...

but i dont get any output on serial monitor. Do you know whaat is went wrong?
thanks

[Anticimex]

@meddie it is a limitation of the current personalizer that it does not inherit the baud rate from the library settings. It is stuck to 115200. (can be changed of course). It will be fixed in the next personalizer update. Perhaps you expect a different baud rate?
See

Serial.begin(115200);

[meddie]

yes i have seen this an my console is set to 115200 bauds, but no output

[Anticimex]

Hm. Then I don't know what's wrong. I have not yet used that hardware.

[meddie]

i just get the output, the serial console must be open while uploading the sketch, immedialty after the upload i see the output.
But all Keys are FFFFFFF

SOFT_HMAC_KEY | FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
SOFT_SERIAL   | FFFFFFFFFFFFFFFFFF
AES_KEY       | FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
ATSHA204A DATA:

Why this?

[tbowmo]

The personalizer doesn't wait for the usb port to be enumerated / attached. We need to add the following code in the start of setup() (if I remember right)

While(! Serial()) {} 

But only for devices using native USB (I thought that I had added it already, but I might be wrong)

[Anticimex]

@tbowmo ah, I will add that then for samd targets. The personalizer uses MY_CORE_ONLY so your line perhaps is not run.

[tbowmo]

@Anticimex
I think something in the line of

#if defined(ARDUINO_ARCH_SAMD)
while (!Serial) {} // halts operation until something attaches to the USB device
#endif

above, is based on hwInit function in MyHwSAMD.cpp

[Anticimex]

@tbowmo Yep, I have already (locally) done this:

#if defined(ARDUINO_ARCH_SAMD)
	while(!Serial()); // Wait for USB enumeration before setting up serial device
#endif
	Serial.begin(MY_BAUD_RATE);

[Anticimex]

I have moved the signing specific discussion in this thread here where it belongs.

[Fleischtorte]

hi all,

i have some problems to enable encryption on the gateway. When i upload the cleareeprom sketch, the gateway dont clear the eeprom,
the same problem comes up when i want to set the ENC-Key. Both sketches work with my moteino-gateway and my ProMini-Node, so do i miss something with the SensebenderGW-Config?

ClearEEPROM:

#if defined(ARDUINO_ARCH_SAMD)
while (!Serial) {} // Wait for USB enumeration before setting up serial device
#endif
  Serial.begin(MY_BAUD_RATE);
	Serial.println("Started clearing. Please wait...");
	for (int i=0; i<EEPROM_LOCAL_CONFIG_ADDRESS; i++) {
		hwWriteConfig(i,0xFF);
	}
	Serial.println("Clearing done. You're ready to go!");

Set ENC-Key:

 #if defined(ARDUINO_ARCH_SAMD)
 while (!Serial) {} // Wait for USB enumeration before setting up serial device
 #endif
  Serial.begin(MY_BAUD_RATE);
  Serial.println("Set ENC-Key. Please wait...");
    uint8_t key[32];
    memcpy(key, user_aes_key, 16);
    hwWriteConfigBlock((void*)key, (void*)EEPROM_RF_ENCRYPTION_AES_KEY_ADDRESS, 16);
    Serial.println("Set ENC-Key. Done");

[Anticimex]

@Fleischtorte we have confirmed a bug in the I2C eeprom management in the samd platform. A fix is in the works.

[Fleischtorte]

@Anticimex okay, thanks for the fast response

[alexsh1]

@scalz Did you manage to do the 3D case for the PA LNA transceiver for the sensebender gateway please?

[ted]

@Anticimex said in Sensebender Gateway:

MY_CORE_ONLY

Just curious, what does "MY_CORE_ONLY" do? The library mentioned that it should be enabled " if you want to use core functions without loading the framework" . What are the core functions and what is the framework?

[Anticimex]

@ted core functions are things like the HAL and debug logging functionality. Framework means all the presentation message transmissions and handshaking. Basically, MY_CORE_ONLY allow you to leverage the functionality provided by the library without having the library execute things out of your control.

[scalz]

@alexsh1
woops, yes i made it but forgot the upload. it's now uploaded here https://www.mysensors.org/hardware/sensebender-gateway#design-files

Enjoy

[alexsh1]

@scalz Thank you.

Does anyone have the PA transceiver version with Sensebender Gateway?
Any feedback please?

[tbowmo]

@alexsh1

If you mean using a nrf24 with lna/pa, with the gateway. Then yes.. I have had it running for some months now.

Anything in particular that you want to know?

[alexsh1]

@tbowmo yes, that's what I meant
I am thinking about installing either a normal nrf24l01+ or lna/pa version. I have had some issues with power in the past with the lna/pa transceiver.
What's your experience? What kind of power supply do you use? How better is the coverage?

[tbowmo]

I haven't checked if the coverage is any better with the lna/pa version, compared to standard modules.

Currently the gateway is connected to a RPI2, which in turn is powered by a 2A powersupply from RS Components

I haven't had any issues with it yet, but then again.. I mainly receive data from sensor nodes, and not that much sending data to distant nodes from the gateway

[alexsh1]

@tbowmo It is probably not Sensebender topic, but more lna+pa range one.
I am not sure about my RPi3 as though it is powered by the 3A PSU, I have a USB z-wave stick, three transceivers, one UPS Plco (as HAT) and a 20x4 screen. I lot of power is consumed so not sure adding yet another one. (lna+pa is power hungry during peaks).

I'll get the nrf24l01+ lna+pa ordered and test the range. In my view rfm69 range is probably better, but I have the rfm69 gateway on moteino with a trace antenna (very small footprint and it is based on ATMega1284P so 128KB sketch flash memory - more than I need).

@hek - is it the intention to combine rfm69 and nrf24l01+ gateways in one in the future?
I understand Sensebender GW is ready for it, but it is more a software limitation???
I am really looking forward to combined GW.
I also have a separate one for rfm95 so that I can use some remote sensors.

[hek]

No, I haven't heard of any near plans in the core team about doing multi radio/sub-network support in 2.0.

This requires some extra thoughts and would probably only fit on SAMD/ESP nodes.

[alexsh1]

@hek Which is good as the Sensebender GW is based on SAMD! So it is ready to be the first 2-in-1 GW.
Anyway, keep on doing a great work! I'll patiently wait until the combined GW is there.

[NiklasO]

Ordered from ITEAD. Nice to get rid of this stuff:

Just nudging anything result in problems.
Time to fire up the 3D-printer.

[NiklasO]

Aaaand, it's up! Very good fit (the box).

The box on top is just me trying out different colors of the case.
The one on top has better look. Different brands of PLA.

[nick van alst]

@NiklasO that looks very good!

Are you willing to share your design files with us?
i just ordered my gateway to get rid of cables and lose components a case would really make it complete!

[scalz]

@NiklasO
great
@nick-van-alst
you can get enclosure design files here https://www.mysensors.org/hardware/sensebender-gateway (on page bottom)
I designed different variants so pick which one you need.

[alexsh1]

@meddie said in Sensebender Gateway:

Ok i just connected the W5100 and NRF24 Module and uploaded the GatewayW5100 Sketch and when the upload is done after reset i dont get any output on serial monitor.
The orange, green and red led are lighting.

When i upload the SensebenderGatewaySerial then i get output on serial monitor. It think the problem must be the w5100. But what going wrong?

@meddie Did you figure out what the problem is? I have exactly the same issue

[meddie]

@alexsh1
hi, yes it was very simple the gateway has worked fine in this time, i thought that when nothing shown in serial monitor that the gateway dont work, but it did it, after i connected the gateway to FHEM (my controller) i saw that FHEM connects t mys Gateway.
So it worked all the time

Greets Eddie

[tbowmo]

@alexsh1

Have you tried to enable the debug output in the GatewayW5100 example? I think it is disabled by default, due to the limited memory on the small atmega 328p

[alexsh1]

@tbowmo

Yes, I did

// Enable debug prints to serial monitor
#define MY_DEBUG
#define MY_DEBUG_VERBOSE_SIGNING